This manual is applicable to the following models:
C4.4 Industrial Engine 44400001-UP
SPF343C Trailer Mounted Pumper 44424500-UP
TL1055D Telehandler ML500001-UP (MACHINE) POWERED BY C4.4 Engine
TL1255D Telehandler ML700001-UP (MACHINE) POWERED BY C4.4 Engine
TL1055D Telehandler MNT00001-UP (MACHINE) POWERED BY C4.4 Engine
TL1255D Telehandler MYW00001-UP (MACHINE) POWERED BY C4.4 Engine
TH514C, TH417C, TH407C, TH414C, TH406C, TH337C, TH336C, Telehandler Transmission RCH00001-00149 (MACHINE)
TH406C Telehandler RCH00150-UP (MACHINE) POWERED BY C4.4 Engine
TL1055 Telehandler T7900001-UP (MACHINE) POWERED BY C4.4 Engine
TL1255 Telehandler T8300001-UP (MACHINE) POWERED BY C4.4 Engine
Manual contents:
Fuel Priming Pump – Remove and Install – Manual Priming
Fuel Injection Pump Gear – Remove
Electronic Control Module – Remove and Install
ECM Mounting Bracket – Remove and Install
Alternator – Remove – Engines With an Automatic Belt
Alternator – Remove – Engines Without an Automatic Belt
Alternator – Install – Engines With an Automatic Belt Tensioner
Alternator – Install – Engines Without an Automatic Belt
Electric Starting Motor – Remove and Install
Air Compressor – Remove and Install
Vacuum Pump – Remove and Install
Fuel Injection Pump Gear – Install
Electronic Unit Injector – Remove
Electronic Unit Injector – Install
Turbocharger – Remove – Side Mounted Turbochargers
Turbocharger – Remove – Top Mounted Turbocharger
Turbocharger – Install – Top Mounted Turbocharger
Turbocharger – Install – Side Mounted Turbochargers
Wastegate Solenoid – Remove and Install
Exhaust Manifold – Remove and Install – Side Mounted
Fuel Filter Base – Remove and Install – Secondary Fuel Filter
Exhaust Manifold – Remove and Install – Top Mounted Exhaust
Exhaust Elbow – Remove and Install
Inlet and Exhaust Valve Springs – Remove and Install
Inlet and Exhaust Valves – Remove and Install
Engine Oil Filter Base – Remove and Install
Engine Oil Cooler – Remove
Engine Oil Cooler – Install
Engine Oil Relief Valve – Remove and Install – Engines with a
Engine Oil Relief Valve – Remove and Install – Engines Without
Engine Oil Pump – Remove and Install – Engines Without a
Fuel Transfer Pump – Remove
Water Pump – Remove
Water Pump – Install
Water Temperature Regulator – Remove and Install
Flywheel – Remove
Flywheel – Install
Crankshaft Rear Seal – Remove
Crankshaft Rear Seal – Install
Flywheel Housing – Remove and Install
Crankshaft Pulley – Remove and Install – Engines With an
Crankshaft Pulley – Remove and Install – Engines Without an
Fuel Transfer Pump – Install
Crankshaft Front Seal – Remove and Install
Front Cover – Remove and Install
Gear Group (Front) – Remove and Install
Idler Gear – Remove
Idler Gear – Remove
Idler Gear – Remove
Idler Gear – Install
Idler Gear – Install
Idler Gear – Install
Housing (Front) – Remove
Fuel Manifold (Rail) – Remove and Install
Housing (Front) – Install
Accessory Drive – Remove
Accessory Drive – Disassemble
Accessory Drive – Assemble
Accessory Drive – Install
Crankcase Breather – Remove and Install – Filtered Breather
Crankcase Breather – Remove and Install – Unfiltered Breather
Valve Mechanism Cover – Remove and Install
Valve Mechanism Cover Base – Remove and Install
Rocker Shaft and Pushrod – Remove
Fuel Injection Lines – Remove
Rocker Shaft – Disassemble
Rocker Shaft – Assemble
Rocker Shaft and Pushrod – Install
Cylinder Head – Remove
Cylinder Head – Install
Lifter Group – Remove and Install
Camshaft – Remove and Install
Camshaft Gear – Remove and Install
Camshaft Bearings – Remove and Install
Engine Oil Pan – Remove and Install – Aluminum and Pressed
Fuel Injection Lines – Install
Engine Oil Pan – Remove and Install – Cast Iron Oil Pan
Balancer – Remove
Balancer – Install
Piston Cooling Jets – Remove and Install
Pistons and Connecting Rods – Remove
Pistons and Connecting Rods – Disassemble
Pistons and Connecting Rods – Assemble
Pistons and Connecting Rods – Install
Connecting Rod Bearings – Remove – Connecting rods in
Connecting Rod Bearings – Install – Connecting rods in position
Fuel Injection Pump – Remove
Crankshaft Main Bearings – Remove and Install – Crankshaft
Crankshaft Main Bearings – Remove and Install – Crankshaft
Crankshaft – Remove
Crankshaft – Install
Crankshaft – Install
Crankshaft Timing Ring – Remove and Install
Crankshaft Gear – Remove and Install
Bearing Clearance – Check
Crankshaft Position Sensor – Remove and Install
Position Sensor (Fuel Injection Pump) – Remove and Install
Fuel Injection Pump – Install
Coolant Temperature Sensor – Remove and Install
Engine Oil Pressure Sensor – Remove and Install
Fuel Pressure Sensor – Remove and Install
Boost Pressure Sensor – Remove and Install
Inlet Air Temperature Sensor – Remove and Install
Glow Plugs – Remove and Install
V-Belts – Remove and Install – Engines Without an Automatic
Alternator Belt – Remove and Install – Engines With an
Fan – Remove and Install
Fan Drive – Remove and Install
Fuel Priming Pump – Remove and Install – Electric Fuel
Reviews
There are no reviews yet.