Service manual Mercedes 711 Transmission

AP26.00-B-2601B Manual transmission – oil change 03.06.2019.pdf
– AP26.00-B-2601B Manual transmission – oil change 03.06.2019
– Transmission 711.622 in model 979.016
– Transmission 715.054 in model 693, 694
– Modification notes
– Transmissions 711, 715 (example)
– 1 Filler plug
AP26.00-D-2601A Manual transmission – oil change 25.02.2019.pdf
– AP26.00-D-2601A Manual transmission – oil change 25.02.2019
– Model 636 with transmission 716.65
– Model 638
– except code G40 (Automatic transmission)
– Model 639 with transmission 716.6
– except code MA0 (E-CELL 60 kW)
– Model 667 with transmission 711.11/13/61
– Model 668 with transmission 710.6, 712.21/613/621, 715.00/02/05
– Model 670 with transmission 710.6/84, 711.61, 712.21/613/621, 714.08/50, 715.00/02/05Model 690.6 with transmission 711.620
– Model 901, 902, 903, 904 with transmission 711.60/61
– Model 901, 902, 903, 904, 905 with transmission 711.62
– Modification notes
– Transmission in model 638
– Transmission 716 in model 636, 639
– N26.00-2319-01 S26.00-4500-01
– Transmission 711, 712, 715 (example)
– Transmission 710 (S5-42)
– N26.00-2268-01 N26.00-0286-01
AP26.00-D-2601H Manual transmission – oil change 26.10.2018.pdf
– AP26.00-D-2601H Manual transmission – oil change 26.10.2018
– Transmission 711.6 in model 906.1/2/6/7
– Transmission 711.68 in model 900
– Transmission 711.680 in model 636, 639
– except code MA0 (E-CELL 60 kW)
– 4 Drain fluid from transmission.
– 5 Screw in drain screw (2). Replace sealing ring on oil drain screw (2).
– *BA26.40-N-1001-01J TRANSMISSION 711.6 in MODEL 636,
– 639Drain screw
– *BA26.40-N-1001-01A Transmission 711.6 in model 906.1/2/6/7
– Transmission 711.68 in model 900Drain screw
– Pour in
– 6 Fill transmission with oil.
– Service Information: Switchover to low-friction Transmission 711.6 in model 639.### ## as of SI00.40-D-0016DJ
AP26.00-D-2605TS Manual transmission – Oil change 14.02.2020.pdf
– AP26.00-D-2605TS Manual transmission – Oil change 14.02.2020
– Transmission 700.790 in model 907
– Transmission 711.6 in model 907
– Modification notes
– 12.02.2020 Gear oil Transmission 711.68 (except 711.683) in BF26.00-N-1001-01A
– model 909 transmission 711.68 (except 711.685) in model 907
– Shown on transmission 711.6
– 1 Filling screw
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AP26.00-S-2601E Manual transmission – oil change 9.10.14.pdf
– AP26.00-S-2601E Manual transmission – oil change 9.10.14
– TRANSMISSION 711.680 in MODEL 447
– Modification notes
– 5 Drain transmission oil
– 6 Screw in drain screw (2) Replace sealing ring on oil drain screw (2).
AR03.30-P-8001CW Remove install flywheel drive plate 10.05.2016.pdf
– 1 Remove the transmission Transmission 722.9 in model 207 with engine AR27.10-P-0500CV
– 271
– Transmission 711.6 in model 172 with engine AR26.10-P-0020V
– Transmission 722.9 in model 172 with engine AR27.10-P-0500W
– Transmission 711.6 in model 204 with engine AR26.10-P-0020SA
– Transmission 711.6 in model 207 with engine AR26.10-P-0020CWA
– Transmission 716.6 in model 204, 207 with AR26.10-P-0020CW
– engine 271
– Transmission 722.6 in model 204.0/2/3 with AR27.10-P-0500CW
– up to model year 2012Transmission 722.6 in model 207 with engine 271
– Transmission 722.997 in model 204 with AR27.10-P-0500CWA
AR22.10-S-0006E Remove install transmission carrier 25.06.2019.pdf
– AR22.10-S-0006E Remove/install transmission carrier 25.06.2019
– Engine 654.9 in model 447
– Shown on transmission 725.0 without code
– ZG2 (Permanent all-wheel drive) with
– 1 Transmission carrier
– 2 AdBlue® line
AR25.10-P-0050CWA Remove install clutch 14.6.11.pdf
– MODEL 207 with TRANSMISSION 711.6, 716.6
– P25.10-2024-09
– 1 Transmission 4 Clutch plate 8 Guide bearing
– 2 Screw 6 Central clutch release bearing 9 Radial shaft seal3 Pressure plate 7 Flywheel 10 Sealing cover
– 1 Remove transmission (1) Transmission 716 AR26.10-P-0020CW
– Transmission 711 AR26.10-P-0020CWA
– 2 Remove bolts (2) and take off pressure plate In order to prevent tilting or warping of the
AR25.10-S-0050E Remove install clutch 20.05.2019.pdf
– Model 447 with engine 651 with transmission 711.6
– Model 447 with engine 654.9 with transmission 711.6
– P25.10-2024-09
– 1 Transmission 5 Adjusting ring 8 Needle bearing
– 2 Screw 6 Central clutch release bearing 9 Radial shaft sealing ring
– 1 Remove transmission (1). Model 447 with engine 651 with transmission AR26.10-S-0020E
– 711.6
– Model 447 with engine 654.9 with transmission AR26.10-S-0021EA
AR25.10-S-0050SD Remove install clutch 19.10.2017.pdf
– Engine 271.951 in model 906 with transmission 711.651
– Engine 642.896 in model 906 with transmission 711.685
– Engine 642.992 in model 906 with transmission 711.660
– Engine 646 in model 636 with transmission 716.6
– Engine 646 in model 639 with transmission 716.6
– Engine 646.984/985/986/989/990 in model 906 with transmission 711.651/660
– Engine 651 in model 636, 639 with transmission 711.6
– Engine 651.955 in model 900 with transmission 711.680Engine 651.955 in model 906.133/135/153/155/631/633/635/655/657 with transmission 710.510
– with code ZL3 (National version for Latin America)
– Engine 651.955/956/957 in model 906 with transmission 711.680
– Engine 651.956 in model 906.133/631/633/635 with transmission 710.510
AR25.20-D-0180SD Remove install central clutch operator 14.12.2016.pdf
– Model 900 with engine 651.955 with transmission 711.680
– Model 906 with engine 271.951, 646.984/985/986/989/990 with transmission 711.651
– Model 906 with engine 642 with transmission 711.685
– Model 906 with engine 642.992, 646.984/985/986/989/990 with transmission 711.660
– Model 906 with engine 651 with transmission 711.680
– Model 906.133/135/153/155/631/633/635/655/657 with engine 651.955 with transmission 710.510
– with code ZL3 (National version for Latin America)
– Model 906.133/631/633/635 with engine 651.956 with transmission 710.510
– Shown on transmission 711.660
– 1 Screw
– 3 Transmission
– D25.20-1109-12
AR26.10-B-0010TG Assemble transmission 16.03.2020.pdf
– AR26.10-B-0010TG Assemble transmission 16.03.2020
– Transmission 712.63 in model 368, 382, 384, 685
– Transmission 712.63 in model 693, 695
– Transmission 712.63 in model 958
– Transmission 712.630/639, 715.06
– Transmission 715.06 in model 382, 384, 685
– Transmission 715.06 in model 695
– Modification notes
– ending 0041837) transmission with “manual”
– actuation)
AR26.10-D-0020G Remove install transmission 23.5.11.pdf
– AR26.10-D-0020G Remove/install transmission 23.5.11
– TRANSMISSION 711.651 in MODEL 906.1 /2 /6 /7 with ENGINE 646.984 /985 /986 /989 /990
– TRANSMISSION 711.660 in MODEL 906.1 /2 /6 /7 with ENGINE 642.992, 646.984 /985 /986 /989 /990
– D26.10-1138-09
– Shown on transmission 711.651 with code (N05) Power take-off
– countershaft (2c) without flange
– code (JD2) EU digital tachograph with rpm and additional 6 Transmission crossmember
– recorder)7 Shift cables
– 8 Transmission
– 9 Exhaust bracket
AR26.10-D-0020H Remove install transmission 06.03.2020.pdf
– AR26.10-D-0020H Remove/install transmission 06.03.2020
– Transmission 710.510 in model 906.133/135/153/155/631/633/635/655/657
– with code ZL3 (National version for Latin America)
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– Modification notes
– Shown on transmission 711.680
– 1 Transmission
– 2 Support plate
AR26.10-D-0020NG Remove install transmission 23.5.11.pdf
– AR26.10-D-0020NG Remove/install transmission 23.5.11
– TRANSMISSION 711.651 in MODEL 906 with ENGINE 271.951
– D26.10-1145-09
– 1 Transmission B6 Speed sensor (on vehicles without B6/12 Speed sensor (on vehicles
– code (J19) Automatic 1 day / 2 with code (J19) tachograph 1 2 Bracket
AR26.10-D-0020TSR Remove install transmission 10.03.2020.pdf
– AR26.10-D-0020TSR Remove/install transmission 10.03.2020
– Model 907 with engine 642, 651 with transmission 711.6
– Model 907.1/2/6 with engine 654.9 with transmission 711.6
– Modification notes
– 08.01.2020 Bolt, speed sensor for tachograph to transmission Transmission 711.680/683/685 BA26.19-N-1001-01I
– 12.02.2020 Work procedure revised.
– 12.02.2020 Gear oil Transmission 711.68 (except 711.683) in BF26.00-N-1001-01A
– model 909 Transmission 711.68 (except
– 711.685) in model 907
AR26.10-D-0036A Fasten transmission on assembly stand 17.6.11.pdf
– AR26.10-D-0036A Fasten transmission on assembly stand 17.6.11
– TRANSMISSION 711.651 in MODEL 906 with ENGINE 271.951, 646.984 /985 /986 /989 /990
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 /990
– TRANSMISSION 711.670 in MODEL 204 with ENGINE 642, 651
– TRANSMISSION 711.680 in MODEL 906
– TRANSMISSION 711.685 in MODEL 906TRANSMISSION 711.670 in MODEL 207 with ENGINE 651
– TRANSMISSION 711.680 in MODEL 900 with ENGINE 651.955
– D26.50-1252-09
– 1 Remove transmission Model 204 with transmission 711.67 AR26.10-P-0020SA
– Model 207 with transmission 711.67 AR26.10-P-0020CWA
– Model 900 with transmission 711.680 AR26.10-D-0020H
– Model 906 with transmission 711.680/685
– Model 906 with transmission 711.65 and AR26.10-D-0020NG
– engine 271
– Model 906 with transmission 711.65 and AR26.10-D-0020G
– engine 646 or with transmission 711.66 and
– engine 642, 646
AR26.10-P-0020CWA Remove install transmission 13.12.11.pdf
– AR26.10-P-0020CWA Remove/install transmission 13.12.11
– TRANSMISSION 711.6 in MODEL 207
– 1 Transmission
– 2 Exhaust clamp
AR26.10-S-0001SD Disassemble assemble transmission 8.6.10.pdf
– AR26.10-S-0001SD Disassemble, assemble transmission 8.6.10
– TRANSMISSION 716.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– S26.10-4502-09
– Shown on transmission 716 without permanent all-wheel drive,
– code ZG2
– 1 Input shaft 6 Front section of transmission housing
– 2 Screw 7 Transmission housing rear section
– 3 Countershaft
– 1 Drain transmission oil
– Manual transmission – oil change AP26.00-D-2601A
– 2 Remove transmission AR26.10-S-0020SD
– Disassemble
– 3 Attach transmission to assembly stand AR26.10-S-0036SD
– 4 Move transmission into the vertical position Input end uppermost.
– 5 Remove radial shaft sealing ring of drive shaft AR26.40-S-4780SD
AR26.10-S-0020E Remove install transmission 09.01.2020.pdf
– AR26.10-S-0020E Remove/install transmission 09.01.2020
– Model 447 with engine 651 with transmission 711.6
– Modification notes
– 08.01.2020 Bolt, speed sensor for tachograph to transmission Transmission 711.680/683/685 BA26.19-N-1001-01I
– S26.10-4517-09
– 1 Bracket 3 Electrical connector 5 Transmission
– 2 Shift cable 4 Hydraulic line W11/1 Engine ground point
– B6/34 Manual transmission speed Hall sensor
– S26.10-4516-01
AR26.10-S-0020EG Remove install transmission 20.5.15.pdf
– AR26.10-S-0020EG Remove/install transmission 20.5.15
– Model 447 with engine 274 with transmission 710.5
– S26.10-4527-09
– 1 Bracket 3 Transmission 5 Securing clamp
– 2 Shift cable 4 Hydraulic line W11/1 Engine ground point
AR26.10-S-0020SD Remove install transmission 24.8.15.pdf
– AR26.10-S-0020SD Remove/install transmission 24.8.15
– Transmission 716.6 in model 636, 639
– Shown on vehicle as from vehicle identification number (VIN)
AR26.10-S-0020SJ Remove install transmission 09.01.2020.pdf
– AR26.10-S-0020SJ Remove/install transmission 09.01.2020
– Transmission 711.6 in model 636, 639 with engine 651
– Modification notes
– 08.01.2020 Bolt, speed sensor for tachograph to transmission Transmission 711.680/683/685 BA26.19-N-1001-01I
– S26.10-4504-09
AR26.10-S-0036SD Fasten transmission on assembly stand 17.09.2013.pdf
– AR26.10-S-0036SD Fasten transmission on assembly stand 17.09.2013
– TRANSMISSION 711.6 in MODEL 636, 639
– TRANSMISSION 716.6 in MODEL 636, 639
– Shown on transmission 716.6
– 1 Transmission
– 2 Bolts
– 1 Remove transmission (1) TRANSMISSION 711.6 AR26.10-S-0020SJ
– Transmission 716.6 AR26.10-S-0020SD
– 2 Remove dowel pins on front section of TRANSMISSION 716.6
– transmission housing
– Installation: Knock the dowel pins approx.
AR26.10-W-0010HC Assemble transmission 09.11.2017.pdf
– AR26.10-W-0010HC Assemble transmission 09.11.2017
– Transmission 715.310 in model 963, 964, 967
– with code G1E (Transmission G 140-8/9.30-0.79)
– W26.10-1178-09
– 1 Compressed-air line 15 Rear section of transmission 29 Drive shaft bearing cap
– housing
– 4 Front section of transmission 18 Output flange 34 Pulse wheel
AR26.19-D-0003A Remove install neutral position switch 08.09.2017.pdf
– Transmission 711.6 in model 906
– Shown with code ZG1 (All-wheel drive,
– S164 Transmission neutral position switch
– D26.19-1178-06
– *BA26.40-N-1022-01A Screw/bolt, transmission neutral switch
– 3 Disconnect electrical connection (2)
AR26.19-D-0032A Remove install neutral position sensor 08.09.2017.pdf
– Transmission 711.6 in model 906
– 1 Electrical connector
– B79/2 Transmission neutral position
– position sensor
AR26.19-D-0032TS Remove install neutral position sensor 15.02.2018.pdf
– Transmission 711.6 in model 907
– 1 Sensor
AR26.19-S-0003E Remove install neutral position switch 20.05.2019.pdf
– Model 447 with transmission 711.6
– with code E07 (Start-off assist)
– B79/2 Transmission neutral position
– position sensor
AR26.19-S-0003S Remove install neutral position switch 21.6.11.pdf
– TRANSMISSION 716.6 in MODEL 636, 639 with CODE (E07) Starting-off aid without time limit
– TRANSMISSION 711.6 in MODEL 639 with CODE (E07) Starting-off aid without time limit
– Shown on model 639 with code (ZG2) Permanent all-wheel drive
– S164 Transmission neutral position switch
– S26.19-4501-11
AR26.40-D-0345TSR Remove install central clutch operator 17.12.2019.pdf
– Model 907 with transmission 711.6
– 1 Transmission
– 2 Central clutch release bearing
– 1 Remove transmission (1). Model 907 with engine 642, 651 with AR26.10-D-0020TSR
– transmission 711.6Model 907.1/2/6 with engine 654.9 with transmission 711.6
– 2 Remove central clutch release bearing (2).
– bearing of transmission
– To do so, remove bolts (3).
AR26.40-D-2002D Disassemble assemble transmission housing 06.03.2020.pdf
– AR26.40-D-2002D Disassemble/assemble transmission housing 06.03.2020
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990
– Transmission 711.670 in model 204 with engine 642, 651
– Transmission 711.670 in model 207 with engine 651
– D26.40-1157-09
– Shown on transmission 711.660
– 1 Front section of transmission housing 5 Guide sleeves 9 Inner bearing race
– 2 Housing extension 6 Guide sleeves 10 Screw3 Rear section of transmission housing 7 Roller bearing 11 Cap
– 4 Screw 8 Drive shaft
– 1 Remove transmission Transmission 711.651 in model 906.1/2/6/7 AR26.10-D-0020G
– with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7
– with engine 642.992, 646.985/986/989/990
– Transmission 711.670 in model 204 with AR26.10-P-0020SA
– engine 642, 651
AR26.40-D-2002E Disassemble assemble transmission housing 17.6.11.pdf
– AR26.40-D-2002E Disassemble/assemble transmission housing 17.6.11
– TRANSMISSION 711.680 in MODEL 906
– TRANSMISSION 711.685 in MODEL 906
– TRANSMISSION 711.680 in MODEL 900
– Shown on transmission 711.685
– 1 Roller bearing
– (only transmission 711.685)
– 5 Drive shaft
– 7 Front section of transmission housing8 Screw
– 9 Rear section of transmission housing
– D26.40-1171-06
– 1 Remove transmission AR26.10-D-0020H
– 2 Fasten transmission on assembly stand AR26.10-D-0036A
– Disassemble
– 4 Turn transmission until drive shaft (5) points
– upward
AR26.40-D-2002TSR Disassemble assemble transmission housing 18.12.2019.pdf
– AR26.40-D-2002TSR Disassemble/assemble transmission housing 18.12.2019
– Transmission 711.6 in model 907
– Shown on transmission 711.685
– 1 Roller bearing
– 3 Screw4 Inner bearing race (transmission
– 711.685)
– 7 Transmission housing front section
– 8 Screw9 Transmission housing rear section
– D26.40-1171-06
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.40-D-2471D Disassemble assemble front section of transmission housing 29.10.2015.pdf
– AR26.40-D-2471D Disassemble/assemble front section of transmission housing 29.10.2015
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990
– Transmission 711.670 in model 204 with engine 642, 651
– Transmission 711.670 in model 207 with engine 651
– 1 Front section of transmission housing
– 2 Bearing sleeve
– 7 Inner bearing race (only transmission
– 711.660 in model 906.1/2/6/7 with engine 642.992, transmission 711.670 in model 204 with engine 642, transmission 711.670 in model 207
– with engine 651)
– 8 Bearing (only transmission 711.660 in
– model 906.1/2/6/7 with engine 642.992, transmission 711.670 in model 204 with engine 642,
– transmission 711.670 in model 207
– 9 Bearing (only transmission 711.651 in
– model 906.1/2/6/7 with engine 646.984/985/986/989/990, transmission
– 711.660 in model 906.1/2/6/7 with
AR26.40-D-2471E Disassemble assemble front section of transmission housing 17.6.11.pdf
– AR26.40-D-2471E Disassemble/assemble front section of transmission housing 17.6.11
– TRANSMISSION 711.680 in MODEL 906
– TRANSMISSION 711.680 in MODEL 900
– 1 Front section of transmission housing
– 2 Drive shaft
– 1 Remove transmission AR26.10-D-0020H
– 2 Fasten transmission on assembly stand AR26.10-D-0036A
– 3 Remove central clutch release bearing AR25.20-D-0180SD
– 4 Remove front section of transmission housing AR26.40-D-2002E
– (1)
AR26.40-D-2471F Disassemble assemble front section of transmission housing 6.3.09.pdf
– AR26.40-D-2471F Disassemble/assemble front section of transmission housing 6.3.09
– TRANSMISSION 711.685 in MODEL 906
– 1 Front section of transmission housing
– 2 Input shaft
– 1 Remove the transmission AR26.10-D-0020H
– 2 Attach transmission to assembly stand AR26.10-D-0036A
– 3 Remove the central clutch release bearing AR25.20-D-0180SD
– 4 Remove front section of transmission housing AR26.40-D-2002E Refer to Disassemble/assemble
– (1) transmission housing.
– Disassemble
AR26.40-D-2471TSR Disassemble assemble front section of transmission housing 18.12.2019.pdf
– AR26.40-D-2471TSR Disassemble/assemble front section of transmission housing 18.12.2019
– Transmission 711.6 in model 907
– Shown on transmission 711.685
– 1 Transmission housing front section
– 2 Drive shaft
– 7 Inner bearing race (transmission
– 711.685)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.40-D-2475-03A Remove install output flange.pdf
– Transmission 711.651 in model 906 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906 with engine 642.992, 646.985/986/989/990
– except code ZG1 (Engageable all-wheel drive)
– Number Designation Transmission Transmission
– 711.651 711.660
AR26.40-D-2475-06A Unscrew screw on shift unit and intermediate.pdf
– Model 204 with engine 642, 651 with transmission 711.670
– Model 207 with engine 651 with transmission 711.670
– Model 212 with transmission 711.670
– Model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990 with transmission 711.660
– Model 906.1/2/6/7 with engine 646.984/985/986/989/990 with transmission 711.651
– Gear set, shafts
– Number Designation Transmission Transmission
– 711.660 711.670
– BA26.50-N-1008-01D Screw/bolt, mounting plate to transmission housing Nm 28 28
– 711.651 711.660
– BA26.50-N-1010-01D Screw/bolt, shift unit to transmission housing M6 Nm 9 9
– rear section
AR26.40-D-2476D Disassemble assemble rear section of transmission housing 19.10.2017.pdf
– AR26.40-D-2476D Disassemble/assemble rear section of transmission housing 19.10.2017
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990
– Transmission 711.670 in model 204 with engine 642, 651
– Transmission 711.670 in model 207 with engine 651
– Modification notes
– 1 Rear section of transmission housing
– 2 Bearing3 Bearing
– 1 Remove transmission Transmission 711.670 in model 207 with AR26.10-P-0020CWA
– engine 651
AR26.40-D-2476E Disassemble assemble rear section of transmission housing 06.11.2017-.pdf
– AR26.40-D-2476E Disassemble/assemble rear section of transmission housing 06.11.2017
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– Modification notes
– 4 Rear section of transmission
– housing
– 19 Screw plugS164 Transmission neutral position switch
– D26.40-1176-06
AR26.40-D-2476E Disassemble assemble rear section of transmission housing 06.11.2017.pdf
– AR26.40-D-2476E Disassemble/assemble rear section of transmission housing 06.11.2017
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– Modification notes
– 4 Rear section of transmission
– housing
– 19 Screw plugS164 Transmission neutral position switch
– D26.40-1176-06
AR26.40-D-2476TSR Disassemble assemble rear section of transmission housing 18.12.2019.pdf
– AR26.40-D-2476TSR Disassemble/assemble rear section of transmission housing 18.12.2019
– Transmission 711.6 in model 907
– D26.40-A000-08
– 4 Rear section of transmission housing 13 Cylindrical roller bearing 18 Guide pin
– 5 Bearing 14 Reverse idler shaft 19 Screw plug
– 6 Screw 15 Bearing 20 Position sensor for transmission
– neutral position (with code E07 (Hill Start Assist) or with code MJ8 (ECO start/stop function))
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.40-D-3258TSR Remove install radial shaft sealing ring at input side 19.04.2018.pdf
– Transmission 711.6 in model 907
– 1 Central clutch release bearing
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.40-D-3840B Remove install output shaft radial shaft sealing ring 17.6.11.pdf
– TRANSMISSION 711.680 in MODEL 906
– TRANSMISSION 711.685 in MODEL 906
– TRANSMISSION 711.680 in MODEL 900
– Shown on transmission 711.685
– 1 Radial shaft seal
– 4 Detach propeller shaft from transmission and AR41.10-D-0050H
– fasten to side of substructure
AR26.40-D-3841TSR Remove install radial shaft sealing ring at output side 06.03.2020.pdf
– Transmission 711.6 in model 907
– except code ZG1 (Engageable all-wheel drive)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.40-D-3841TSX Remove install radial shaft sealing ring at output side 06.03.2020.pdf
– Model 907 with transmission 711.6
– with code ZG1 (Engageable all-wheel drive)
– with code ZG3 (Engageable all-wheel drive with gear reduction)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.40-S-0345E Remove install central clutch operator 20.05.2019.pdf
– Model 447 with engine 651 with transmission 711.6
– Model 447 with engine 654.9 with transmission 711.6
– 1 Transmission
– 2 Central clutch release bearing
– 1 Remove transmission (1). Model 447 with engine 654.9 with transmission AR26.10-S-0021EA
– 711.6
– Model 447 with engine 651 with transmission AR26.10-S-0020E
AR26.40-S-0345SD Remove install central clutch operator 18.09.2013.pdf
– TRANSMISSION 711.6 in MODEL 636, 639
– TRANSMISSION 716.6 in MODEL 636, 639
– 1 Transmission
– 2 Central clutch release bearing
– 1 Remove transmission (1) Transmission 716.6 AR26.10-S-0020SD
– TRANSMISSION 711.6 AR26.10-S-0020SJ
– 2 Remove central clutch release bearing (2)
AR26.40-S-2002E Disassemble assemble transmission housing 06.03.2020.pdf
– AR26.40-S-2002E Disassemble/assemble transmission housing 06.03.2020
– Model 447 with transmission 711.6
– 1 Roller bearing
– 6 Front section of transmission housing7 Screw
– 8 Rear section of transmission housing
– S26.40-4505-06
– 1 Drain transmission oil
– Manual transmission – oil change AP26.00-S-2601E
– 2 Fasten transmission on assembly stand AR26.10-S-0036E
– Disassemble
– 4 Turn transmission until drive shaft (4) points
– upward
AR26.40-S-2002SJ Disassemble assemble transmission housing 06.03.2020.pdf
– AR26.40-S-2002SJ Disassemble/assemble transmission housing 06.03.2020
– Transmission 711.6 in model 636, 639
– 1 Roller bearing
– 6 Front section of transmission housing7 Screw
– 8 Rear section of transmission housing
– S26.40-4505-06
– 1 Remove manual transmission AR26.10-S-0020SJ
– 2 Secure manual transmission to assembly AR26.10-S-0036SD
– stand
– 4 Turn manual transmission until drive shaft (4)
– points upward
– between the cap (2) and the seat.Otherwise the seat will be damaged and the front section of the transmission housing (6)
– must be replaced.
AR26.40-S-2471E Disassemble assemble front section of transmission housing 05.06.2018.pdf
– AR26.40-S-2471E Disassemble/assemble front section of transmission housing 05.06.2018
– Model 447 with transmission 711.6
– 1 Front section of transmission housing
– 2 Drive shaft
– 1 Remove front section of transmission housing AR26.40-S-2002E
– (1)
AR26.40-S-2471SJ Disassemble assemble front section of transmission housing 05.06.2018.pdf
– AR26.40-S-2471SJ Disassemble/assemble front section of transmission housing 05.06.2018
– Transmission 711.6 in model 636, 639
– except code MA0 (E-CELL 60 kW)
– 1 Front section of transmission housing
– 2 Drive shaft
– 1 Drain transmission oil from manual
– transmission
– Manual transmission – oil change AP26.00-D-2601H
– 2 Remove manual transmission AR26.10-S-0020SJ
– 3 Secure manual transmission to assembly AR26.10-S-0036SD
– stand
– 5 Remove front section of transmission housing AR26.40-S-2002SJ
– (1)
AR26.40-S-2476E Disassemble assemble rear section of transmission housing 19.10.2017.pdf
– AR26.40-S-2476E Disassemble/assemble rear section of transmission housing 19.10.2017
– Model 447 with transmission 711.6
– Modification notes
– 4 Rear section of transmission 11 Thrust plate 18 Guide pin
– housing
– 5 Bearing 12 Reverse gear 19 Screw plug6 Screw 13 Cylindrical roller bearing B79/2 Transmission neutral position
– position sensor
AR26.40-S-2476SD Disassemble assemble rear section of transmission housing 19.10.2017.pdf
– AR26.40-S-2476SD Disassemble/assemble rear section of transmission housing 19.10.2017
– Transmission 716.6 in model 636, 639
– Modification notes
– 1 Rear section of transmission housing
– 2 Locking plates
– 1 Disassemble transmission AR26.10-S-0001SD
– 2 Clamp rear section of transmission housing (1) Clamp in assembly plate in vise first. A
– with assembly plate vertically in vise helper is required.
AR26.40-S-2476SJ Disassemble assemble rear section of transmission housing 19.10.2017.pdf
– AR26.40-S-2476SJ Disassemble/assemble rear section of transmission housing 19.10.2017
– Transmission 711.6 in model 636, 639
– except code MA0 (E-CELL 60 kW)
– 4 Rear section of transmission
– housing
– S164 Transmission neutral position switch
– D26.40-1176-06
AR26.40-S-4780SD Replace radial shaft sealing ring of axle shaft and sealing cover of countershaft 17.09.2013.pdf
– TRANSMISSION 711.6 in MODEL 636, 639
– TRANSMISSION 716.6 in MODEL 636, 639
– Shown on transmission 716.6
– 1 Transmission
– 2 Radial shaft sealing ring
– Shown on transmission 716.63 Sealing cover
– S26.40-4502-04
AR26.45-D-0010-08C Install gear set and shift mechanism of power.pdf
– Number Designation Transmissions Transmissions
– 711.651/660 with 711.680/685 code N05, N07 with code N05,
AR26.45-D-0011B Remove install radial shaft seal for output flange 6.3.09.pdf
– TRANSMISSION 711.651 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange
– TRANSMISSION 711.660 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange
– TRANSMISSION 711.680 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange
– TRANSMISSION 711.685 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange
– Shown on transmission 711.680
– 1 Radial shaft seal
AR26.45-D-0012TSR Remove install radial shaft sealing ring on output flange 06.03.2020.pdf
– Transmission 711.680/685 in model 907
– with code N07 (PTO, layshaft MB, 2b)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.45-D-0015-03A Install power take-off bearing cap.pdf
– Number Designation Transmissions Transmissions
– 711.651/660 with 711.680/685 code N05, N07 with code N05,
AR26.45-D-0016-04A Remove install gearshift lever and shift rod of.pdf
– Number Designation Transmissions
– 711.651/660 with code N05,
– BA26.45-N-1011-01A Bolt, gearshift lever of shift lock to transmission Nm 23
– housing
AR26.45-D-0016B Disassemble assemble PTO 12.4.10.pdf
– TRANSMISSION 711.651 in MODEL 906 with ENGINE 646.984 /985 /986 /989 with CODE (N05) Power take-off countershaft (2c)
– without flange
– TRANSMISSION 711.651 in MODEL 906 with ENGINE 646.984 /985 /986 /989 with CODE (N07) Power take-off countershaft (2b)
– with flange
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 with CODE (N05) Power take-off countershaft
– (2c) without flange
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 with CODE (N07) Power take-off countershaft
– (2b) with flange
– TRANSMISSION 711.680 in MODEL 906 with CODE (N05) Power take-off countershaft (2c) without flange
– TRANSMISSION 711.680 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange
– TRANSMISSION 711.685 in MODEL 906 with CODE (N05) Power take-off countershaft (2c) without flange
– TRANSMISSION 711.685 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange
– Shown on transmission 711.680 with CODE (N07) Power take-off
– countershaft (2b) with flange
– 1 Remove the transmission Transmission 711.651/660 AR26.10-D-0020G
– Transmission 711.680/685 AR26.10-D-0020H
– 2 Attach transmission to assembly stand AR26.10-D-0036A
– 3 Remove front section of transmission housing Refer to Disassemble/assemble
– transmission housing.
– Transmission 711.651/660 AR26.40-D-2002D
– Transmission 711.680/685 AR26.40-D-2002E
– 4 Remove shift shaft Transmission 711.680/685 AR26.60-D-6500A
AR26.45-D-0020-02B Remove install shift cylinder..pdf
– Number Designation Transmissions Transmissions
– 711.651/660 with 711.680/685 code N05, N07 with code N05,
– Shown on transmission 711.680
– 1 Remove the shift cylinder (3), .
AR26.45-D-0043TSR Disassemble assemble power take-off 18.12.2019.pdf
– Transmission 711.680/685 in model 907
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (PTO, layshaft MB, 2b)
– 1 Remove transmission. Transmission 711.6 in model 907 with engine AR26.10-D-0020TSR
– 642, 651 with code N05 (Power take-off countershaft (2c) without flange)Transmission 711.6 in model 907 with engine
– 642, 651
AR26.45-D-0070-01A Remove install output flange of output shaft.pdf
– Number Designation Transmissions Transmissions
– 711.651/660 with 711.680/685 code N05, N07 with code N05,
AR26.45-D-0070-01TSR Remove install output flange of output shaft.pdf
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Transmission 711.680/685 in model 907
– with code N07 (PTO, layshaft MB, 2b)
– Number Designation Transmission Transmission
– 711.680 in model 711.685906, 907 with code with code N05 N05 (Power take-off (Power take-off countershaft (2c) countershaft (2c)
– transmission Transmission 711.680 in model 711.685906, 907 with code with code N07 N07 (Power take-off (PTO, layshaft MB,
– countershaft MB, 2b)
AR26.45-D-0070B Remove install radial shaft seal for output shaft 23.5.11.pdf
– TRANSMISSION 711.651 in MODEL 906 with ENGINE 646.984 /985 /986 /989
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 except CODE (ZG1) Engageable all-wheel
– drive
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 except CODE (ZG2) Permanent all-wheel driveTRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 except CODE (ZG3) Engageable all-wheel
– drive with gear reduction
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 except CODE (ZG4) Permanent all-wheel drive
– with gear reduction
– Shown: transmission 711.651
– with code N05 power take-off
AR26.45-D-0070C Remove install radial shaft seal for output shaft 23.5.11.pdf
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 with CODE (ZG1) Engageable all-wheel drive
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 with CODE (ZG2) Permanent all-wheel drive
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 with CODE (ZG3) Engageable all-wheel drive
– with gear reduction
– TRANSMISSION 711.660 in MODEL 906 with ENGINE 642.992, 646.985 /986 /989 with CODE (ZG4) Permanent all-wheel drive
AR26.45-D-1000A Bleed power take-off 08.02.2019.pdf
– Transmission 711 in model 906
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (Power take-off countershaft (2b) with flange)
AR26.45-D-1000TSR Bleed power take-off 05.03.2019.pdf
– Transmission 711.680/685 in model 907
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (PTO, layshaft MB, 2b)
AR26.45-D-1001A Remove install switchover valve 16.02.2017.pdf
– Transmission 711 in model 906
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (Power take-off countershaft (2b) with flange)
AR26.45-D-1001TSR Remove install switchover valve 05.03.2019.pdf
– Transmission 711.680/685 in model 907
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (PTO, layshaft MB, 2b)
AR26.45-D-1002A Remove install power take-off slave cylinder 08.02.2019.pdf
– Transmission 711 in model 906
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (Power take-off countershaft (2b) with flange)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.45-D-1002TSR Remove install power take-off slave cylinder 06.03.2020.pdf
– Transmission 711.680/685 in model 907
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (PTO, layshaft MB, 2b)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR26.45-D-1003A Remove install power take-off master cylinder 08.02.2019.pdf
– Transmission 711 in model 906
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (Power take-off countershaft (2b) with flange)
AR26.45-D-1003TSR Remove install power take-off master cylinder 05.03.2019.pdf
– Transmission 711.680/685 in model 907
– with code N05 (Power take-off countershaft (2c) without flange)
– with code N07 (PTO, layshaft MB, 2b)
AR26.45-S-0070E Remove install radial shaft seal for output shaft 20.05.2019.pdf
– Model 447 with transmission 711.6
– Modification notes
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– 1.2 Remove transmission carrier. Model 447 with engine 654.9
– AR22.10-S-0006E
– 2 Remove transmission mount. Model 447 with engine 654.9 AR22.10-S-0007E
– 3.1 Detach propeller shaft with flex disk from Model 447 with engine 651
– transmission.
– AR41.10-S-0050-14E
– transmission
– *BA41.10-N-1003-01H Bolt, propeller shaft center support
AR26.45-S-0070SD Remove install radial shaft seal for output shaft 04.06.2018.pdf
– Transmission 711.6 in model 636, 639
– Transmission 716.6 in model 636, 639
– Modification notes
– Shown on TRANSMISSION 716.6 without
– CODE ZG2 (Permanent all-wheel drive)
– Shown on TRANSMISSION 716.6 with CODE ZG2 (Permanent all-wheel drive)
– 3 Radial shaft sealing ring
AR26.50-D-0002A Remove install main shaft and countershaft with shift unit 04.06.2018.pdf
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990
– Transmission 711.670 in model 204 with engine 642, 651
– Transmission 711.670 in model 207 with engine 651
– Transmission 711.660 shown
– 1 Puller
– 2 Rear section of transmission
– housing
– S164 Transmission neutral position switch
– D26.40-1165-06
AR26.50-D-0002B Remove install main shaft and countershaft with shift unit 17.6.11.pdf
– TRANSMISSION 711.680 in MODEL 906
– TRANSMISSION 711.685 in MODEL 906
– TRANSMISSION 711.680 in MODEL 900
– D26.50-1310-09
– Transmission 711.685 shown
– 1 Nut 7 Main shaft 13 Inner bearing race (transmission
– 711.685) 2 Output flange 8 Shift fork
– 14 Countershaft 3 Rear section of transmission housing 9 Shift fork
– 15 Screw (transmission 711.685) 4 Intermediate plate (transmission 10 Shift fork
– 711.685) 16 Fitting sleeve (transmission 711.685)11 Support fixture
– 5 Bearing cap (transmission 711.685)12 Shift fork
– 6 Screw (transmission 711.685)
– Modification notes
– Use puller to detach transmission housing rear section. AR26.50-D-0002-03A
– Use puller to detach transmission housing rear section. AR26.50-D-0002-03B
– Removing
AR26.50-D-0002TSR Remove install main shaft and countershaft with shift unit 18.12.2019.pdf
– Transmission 711.6 in model 907
– D26.50-1310-09
– Shown on transmission 711.685 except code ZG1 (All-wheel drive, engageable) and except code ZG3 (Engageable all-wheel drive wit h
– transmission ratio)
– 2 Output flange (except code ZG1 (All- 6 Screws (transmission 711.685) 14 Countershaft
– wheel drive, engageable) and except
– with transmission ratio))
– 3 Rear section of transmission housing 7 Main shaft 15 Screw (transmission 711.685)4 Intermediate plate (transmission 11 Support fixture 16 Pilot bushing (transmission 711.685)
– 711.685)
– 5 Bearing cap (transmission 711.685) 13 Inner bearing race (transmission
AR26.50-D-0420F Disassemble and assemble main shaft 29.10.15.pdf
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– D26.50-1225-09
– 1 Remove the transmission AR26.10-D-0020G
– 2 Attach transmission to assembly stand AR26.10-D-0036A
– 3 Disassemble transmission housing AR26.40-D-2002D
– 4 Remove main shaft (19) AR26.50-D-0002A
AR26.50-D-0420G Disassemble and assemble main shaft 16.6.09.pdf
– TRANSMISSION 711.660 in MODEL 906.1 /2 /6 /7 with ENGINE 642.992, 646.985 /986 /989
– TRANSMISSION 711.670 in MODEL 204 with ENGINE 642, 651
– TRANSMISSION 711.670 in MODEL 207 with ENGINE 651
– D26.50-1226-09
– Transmission 711.660 shown
– 1 Synchronizer unit of reverse gear 11 Cone ring 21 Main shaft
– 1 Remove the transmission Model 906 AR26.10-D-0020G
– Model 204 AR26.10-P-0020SA
– 2 Attach transmission to assembly stand AR26.10-D-0036A
– 3 Remove the central clutch release bearing Model 906 AR25.20-D-0180SD
AR26.50-D-0420H Disassemble and assemble main shaft 17.6.11.pdf
– TRANSMISSION 711.680 in MODEL 906
– TRANSMISSION 711.685 in MODEL 906
– TRANSMISSION 711.680 in MODEL 900
– D26.50-1282-09
– (only transmission 711.685) 2 Friction ring 30 Friction ring
– 17 Intermediate plate roller bearing 3 Cone ring 31 Bearing sleeve
– (only transmission 711.685) 4 Synchronizer ring 32 1st gear needle roller bearing
– 18 Main shaft 5 Sliding sleeve 33 1st gear idler gear
AR26.50-D-0420TSR Disassemble and assemble main shaft 18.12.2019.pdf
– Transmission 711.6 in model 907
– D26.50-1282-09
– Shown on transmission 711.685
– 1 Clutch body 15 3rd gear needle bearing 29 Cone ring
– (transmission 711.685)
– 3 Cone ring 17 Outer bearing race (transmission 31 Distance sleeve
– 711.685)
AR26.50-D-2002-01C Remove install reverse idler shaft with reverse.pdf
– transmission housing
– 1 Screw
– 7 Rear section of transmission housing
– D26.50-1209-11
AR26.50-D-4775D Disassemble assemble countershaft 30.10.15.pdf
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– D26.50-1264-09
– 1 Remove the transmission AR26.10-D-0020G
– 2 Attach transmission to assembly stand AR26.10-D-0036A
– 3 Disassemble transmission housing AR26.40-D-2002D
– 4 Remove countershaft (18) AR26.50-D-0002A
AR26.50-D-4775TSR Disassemble assemble countershaft 18.12.2019.pdf
– Transmission 711.6 in model 907
– D26.50-1283-09
– 1 Retaining ring 8 Sliding sleeve 14 Spacer disk (with transmission
– 711.685)
– 5 6th gear needle bearing 12 Cone ring (with transmission 711.685) 18 Intermediate shaft roller bearing (with
– transmission 711.685)
– 6 Sleeve 13 Friction ring (with transmission 19 Washer
AR26.50-S-0002E Remove install main shaft and countershaft with shift unit 04.06.2018.pdf
– Model 447 with transmission 711.6
– S26.50-4528-09
– 2 Output flange 6 Shift fork 10 Countershaft3 Rear section of transmission housing 7 Shift fork
– 4 Main shaft 8 Support fixture
– 1 Fasten transmission on assembly stand AR26.10-S-0036E
– 2 Remove front section of transmission housing AR26.40-S-2002E
– 3 Remove shift shaft AR26.60-S-6500E
– 4 Insert gear set with transmission housing rear AR26.40-S-2475-07E
– section (3) into support fixture (8)
AR26.50-S-0002SJ Remove install main shaft and countershaft with shift unit 04.06.2018.pdf
– Transmission 711.6 in model 636, 639
– except code MA0 (E-CELL 60 kW)
– 3 Rear section of transmission housing 7 Shift fork
– 4 Main shaft 8 Support fixture
– 1 Remove manual transmission AR26.10-S-0020SJ
– 2 Secure manual transmission to assembly AR26.10-S-0036SD
– stand
– 3 Remove front section of transmission housing AR26.40-S-2002SJ
– 4 Remove shift shaft AR26.60-S-6500SJ
– 5 Insert gear set with transmission housing rear AR26.40-S-2475-07SJ
– section (3) into support fixture (8)
AR26.50-S-0420E Disassemble and assemble main shaft 05.06.2018.pdf
– Model 447 with transmission 711.6
– S26.50-4523-09
– 1 Fasten transmission on assembly stand AR26.10-S-0036E
– 2 Disassemble transmission housing AR26.40-S-2002E
– 3 Remove main shaft (18) AR26.50-S-0002E
AR26.50-S-0420SJ Disassemble and assemble main shaft 05.06.2018.pdf
– Transmission 711.6 in model 636, 639
– except code MA0 (E-CELL 60 kW)
– 1 Remove manual transmission AR26.10-S-0020SJ
– 2 Secure manual transmission to assembly AR26.10-S-0036SD
AR26.60-D-0004M Remove install gearshift linkage 06.04.2018.pdf
– Transmission 711.680 in model 900, 906
– Transmission 711.680/683 in model 909
– Transmission 711.685 in model 906
– Shown on model 906
– 1 Raise vehicle. Model 909 with transmission 711.680/683 AR00.60-D-1000F
– Model 900, 906 with transmission 711.680 AR00.60-D-1000H
– Model 906 with transmission 711.685
– 2 Remove shift cables at transmission from ball Transmission 711.685 in model 906 with AR26.60-D-6626-01A
– heads. engine 642.896
– Transmission 711.680/683 in model 909 AR26.60-D-6626-01R
– Transmission 711.680 in model 900, 906 AR26.60-D-6626-01B
– Transmission 711.685 in model 906 with engine 642.992Transmission 711.685 in model 906 with engine 642.993
– 3 Remove shift gate linkage (1) from mounts (2)
AR26.60-D-0635-02TS Adjust shift cables.pdf
– Transmission 700.76 in model 910
– Shift cable with sliding piece
– Transmission 700.790 in model 907
– Transmission 711.6 in model 907
AR26.60-D-0635-02TSS Adjust shift cables.pdf
– Transmission 700.76 in model 910
– Shift cable with safety clip
– Transmission 711.6 in model 907
AR26.60-D-6500A Remove install shift shaft 06.03.2020.pdf
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– Modification notes
– 1 Remove transmission AR26.10-D-0020H
– 2 Fasten transmission to the assembly stand AR26.10-D-0036A
– and turn to horizontal position
– 3 Shift transmission at gearshift linkage to
– neutral
AR26.60-D-6500TSR Remove install shift shaft 18.12.2019.pdf
– Transmission 711.6 in model 907
– 1 Cover
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– 1 Remove transmission. Transmission 711.6 in model 907 with engine AR26.10-D-0020TSR
– 642, 651
– Transmission 711.6 in model 907.1/2/6 with
– engine 654.9
AR26.60-D-6506A Remove install counterweight of gearshift shaft 20.07.2020.pdf
– Transmission 711.68 in model 900, 906
– D26.60-A000-09
– Shown on model 906 with transmission 711.680
– 1 Retaining bracket 4 Connecting strut
– 3 Remove shift cables (3) from transmission. Transmission 711.685 in model 906 with AR26.60-D-6626-01A
– engine 642.896
– Transmission 711.680 in model 900, 906 AR26.60-D-6626-01B
– Transmission 711.685 in model 906 with engine 642.992
– Transmission 711.685 in model 906 with
AR26.60-D-6506TSR Remove install counterweight of gearshift shaft 20.07.2020.pdf
– Transmission 711.6 in model 907
– D26.60-A000-09
– Shown on model 906 with transmission 711.680
– 3 Shift cables 4 Connecting strut 5 Counterweight
– 3 Remove shift cables (3) from transmission. AR26.60-D-6626-01TS
– Long-life grease *BR00.45-Z-1001-06A
AR26.60-D-6610-01A Detach attach switching unit.pdf
– Transmission 710.510 in model 906.133/135/153/155/631/633/635/655/657
– with code ZL3 (National version for Latin America)
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– Shift
– Number Designation Transmission Transmission
– 710.510 711.651
AR26.60-D-6610B Remove install shift device 07.08.2018.pdf
– Transmission 710.510 in model 906.133/135/153/155/631/633/635/655/657
– with code ZL3 (National version for Latin America)
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– 1 Shift gate
AR26.60-D-6611TS Remove install shift gate 04.06.2019.pdf
– Model 907 with transmission 700.790
– Model 907 with transmission 711.6
– Model 910 with transmission 700.76
– 1 Shift gate
AR26.60-D-6626-01A Detach attach shift cables at transmission.pdf
– AR26.60-D-6626-01A Detach/attach shift cables at transmission
– Transmission 711.651 in model 906.1/2/6/7 with engine 271.951, 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.984/985/986/989/990
– Transmission 711.685 in model 906 with engine 642.896
– Repair materials
– 1 Detach ball heads (4) from transmission.
– 2 Unlock retainers (3) and detach shift cables (2) from transmission.
AR26.60-D-6626-01B Detach attach shift cables at transmission.pdf
– AR26.60-D-6626-01B Detach/attach shift cables at transmission
– Transmission 710.510 in model 906.133/135/153/155/631/633/635/655/657
– with code ZL3 (National version for Latin America)
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906 with engine 642.992
– Transmission 711.685 in model 906 with engine 642.993
– Repair materials
AR26.60-D-6626-01R Detach attach shift cables at transmission.pdf
– AR26.60-D-6626-01R Detach/attach shift cables at transmission
– Transmission 711.680/683 in model 909
– Repair materials
AR26.60-D-6626-02A Detach attach shift cables at switching unit.pdf
– Transmission 710.510 in model 906.133/135/153/155/631/633/635/655/657
– with code ZL3 (National version for Latin America)
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– Repair materials
AR26.60-D-6626B Remove install shift cables 07.08.2018.pdf
– Transmission 710.510 in model 906.133/135/153/155/631/633/635/655/657
– with code ZL3 (National version for Latin America)
– Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990
– Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– 1 Shift gate
– 2 Transmission
– 3 Shift cables
AR26.60-D-6626TS Remove install shift cables 17.08.2018.pdf
– Transmission 700.76 in model 910
– Transmission 711.6 in model 907
– 1 Shift cables
– 1 Shift transmission to neutral position.
– 2 Raise vehicle. Transmission 711.6 in model 907 AR00.60-D-1000-04TS
– Topical note Special instructions for lifting and supporting AH00.60-N-0100-01TS
AR26.60-D-6633B Adjust shift cables for manual transmission 14.12.2016.pdf
– AR26.60-D-6633B Adjust shift cables for manual transmission 14.12.2016
– Transmission 710.510 in model 906.133/135/153/155/631/633/635/655/657
– with code ZL3 (National version for Latin America)
– Transmission 711.680 in model 900
– Transmission 711.680 in model 906
– Transmission 711.685 in model 906
– D26.60-1209-09
– 2 Transmission 5 Zero position catch
– 3 Shift lever boot 6 Sliding piece
– 1 Shift transmission to neutral
– 2 Unclip shift lever boot (3) and slide upward at
AR26.60-S-0072SD Remove install radial shaft seal of shift rod 21.4.09.pdf
– TRANSMISSION 716.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– Shown on transmission 716 without permanent all-wheel drive, code ZG2
– 1 Transmission
– 2 Securing pin
– 1 Remove transmission (1) AR26.10-S-0020SD For vehicles with permanent all-wheel
– drive, code ZG2 the transfer case remains on
– the transmission.
– 2 Remove shift arm with relay lever AR26.60-S-6660SD
AR26.60-S-6500E Remove install shift shaft 06.03.2020.pdf
– Model 447 with transmission 711.6
– 1 Cover
– 1 Drain fluid from transmission.
– Manual transmission – oil change AP26.00-S-2601E
– 2 Remove transmission. Model 447 with engine 654.9 with transmission AR26.10-S-0021EA
– 711.6
– Model 447 with engine 651 with transmission AR26.10-S-0020E
– 3 Secure transmission onto assembly stand and AR26.10-S-0036E
– turn to horizontal position.
– 4 Shift transmission to neutral position.
– 5 Remove linkage (4).
– 7 Clean sealing surfaces at transmission Assembly cleaner *BR00.45-Z-1028-04A
– housing and cap (1).
AR26.60-S-6500SJ Remove install shift shaft 06.03.2020.pdf
– Transmission 711.6 in model 636, 639
– except code MA0 (E-CELL 60 kW)
– 1 Drain transmission oil from manual
– transmission
– Manual transmission – oil change AP26.00-D-2601H
– 2 Remove manual transmission AR26.10-S-0020SJ
– 3 Secure manual transmission to assembly AR26.10-S-0036SD
– stand and turn to horizontal position
– 4 Shift manual transmission to neutral position
– 5 Remove linkage (4)
– 7 Clean sealing surfaces on transmission Assembly cleaner *BR00.45-Z-1028-04A
– housing and on cover (1)
AR26.60-S-6506S Remove install counterweight of gearshift shaft 16.08.2018-.pdf
– Transmission 711.6 in model 447
– Transmission 711.6 in model 636, 639
– S26.60-A000-09
– 1 Raise vehicle. Transmission 711.6 in model 636, 639 AR00.60-S-1000S
– Transmission 711.6 in model 447 AR00.60-S-1000E
– 2 Remove shift cables (1) from transmission. Transmission 711.6 in model 636, 639 AR26.60-S-6626SD
– Transmission 711.6 in model 447 AR26.60-S-6626E
– 3 Remove connecting strut (2) from ball head of
AR26.60-S-6506S Remove install counterweight of gearshift shaft 16.08.2018.pdf
– Transmission 711.6 in model 447
– Transmission 711.6 in model 636, 639
– S26.60-A000-09
– 1 Raise vehicle. Transmission 711.6 in model 636, 639 AR00.60-S-1000S
– Transmission 711.6 in model 447 AR00.60-S-1000E
– 2 Remove shift cables (1) from transmission. Transmission 711.6 in model 636, 639 AR26.60-S-6626SD
– Transmission 711.6 in model 447 AR26.60-S-6626E
– 3 Remove connecting strut (2) from ball head of
AR26.60-S-6604SD Remove install gearshift lever with bearing bracket 15.05.2018.pdf
– Transmission 711.6 in model 636, 639
– Transmission 716.6 in model 636, 639
– 1 Shift cable, outer
AR26.60-S-6633SD Adjust shift cables for manual transmission 15.05.2018.pdf
– AR26.60-S-6633SD Adjust shift cables for manual transmission 15.05.2018
– Transmission 711.6, 716.6 in model 636, 639
– 1 Catch
AR27.10-S-0500SV Remove install transmission with torque converter 15.2.12.pdf
– AR27.10-S-0500SV Remove/install transmission with torque converter 15.2.12
– MODEL 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815 with ENGINE 112.951 /976
– 3 Remove transmission oil filler pipe AR27.10-S-7010SV
– 4 Remove complete exhaust system AR49.10-S-7000SV
AR27.10-S-0510S Disassemble assemble transmission 21.4.09.pdf
– AR27.10-S-0510S Disassemble, assemble transmission 21.4.09
– TRANSMISSION 722.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– N27.10-2021-08
– 2 Transmission housing 6 Multi-disk brake B2
– 3 Drive shaft with clutch K2 and front gear set 7 Park pawl gear4 Output shaft with center and rear gear set 8 Electrohydraulic control unit
– 1 Detach transmission housing (2) from torque AR27.50-S-0601S
– converter housing (1)
AR27.10-S-7010SV Remove install oil filler pipe for automatic transmission 10.11.09.pdf
– AR27.10-S-7010SV Remove/install oil filler pipe for automatic transmission 10.11.09
– MODEL 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815 with ENGINE 112.951 /976
– 17 Transmission housing
– 19 Oil filler pipe
AR27.19-S-0220S Disassemble and assemble electrohydraulic control unit 22.4.09.pdf
– TRANSMISSION 722.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– 15 Caps
AR27.40-S-0510S Disassemble assemble transmission housing 21.4.09.pdf
– AR27.40-S-0510S Disassemble/assemble transmission housing 21.4.09
– TRANSMISSION 722.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– 2 Transmission housing
– 5 Disk pack B3
AR27.50-S-0610S Remove install main components of transmission 21.4.09.pdf
– AR27.50-S-0610S Remove/install main components of transmission 21.4.09
– TRANSMISSION 722.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– N27.10-2021-08
– 2 Transmission housing 6 Multi-disk brake B2
– 3 Drive shaft with K2 clutch and front gear set 7 Park pawl gear4 Output shaft with center and rear gear set 8 Electrohydraulic control unit
– 1 Detach transmission housing (2) from torque AR27.50-S-0601S
– converter housing (1).
AR27.55-S-0600SV Remove install oil lines of oil cooling for automatic transmission 20.11.03.pdf
– AR27.55-S-0600SV Remove/install oil lines of oil cooling for automatic transmission 20.11.03
– MODEL 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815 with ENGINE 112.951 /976
AR28.10-D-0100H Remove install transfer case 7.12.09.pdf
– 3 Drain oil in transfer case (1) AR28.10-D-0100-03H Only when the transmission is replaced, or
– when repairs are to be made to the transmission.
– *BA28.40-N-1001-01E
– Automatic transmission fluids (ATF, Sheet Sheet 236.12 BB00.40-P-0236-12A
– 236.12)
AR43.30-G-0002G Remove install retarder 8.6.11.pdf
– MODEL 000.001 with TRANSMISSION 714.100 /120 /140 /143 /160 /161
– with Voith retarder R115E
– 1 Coolant connection 7 Shim 11 Transmission
– 3 Screw 8 Sealing surface 12 Tapered roller bearing
– 1 Drain oil from transmission AP26.00-G-2601E
– 2 Drain oil from retarder AP43.30-G-4301G
– 3 Remove transmission (11) See vehicle operator’s manual or repair
– instructions.
– 4 Detach clutch housing from transmission (11) Only on transmission (11) without integral AR26.30-G-0330G
– clutch housing.
BB00.40-P-0231-02A Specified transmission oils commercial.pdf
– BB00.40-P-0231-02A Specified transmission oils (commercial
– vehicle, van) – Overview
Should be used BB00.40-P-0231-01A Specified gear oils cars cross-country.pdf
– Automated manual transmission 717.4 in model 450, 452
– Automated manual transmission 717.4 in model 451, 454
– DCT (Twinamic) 700.410/411 in model 453
– Manual transmission 700.120/121/122/123 in model 453
– Passenger car, sheets 235.0 to 235.74
SI00.40-D-0016DJ Service Information Switchover to low-friction oil on vehicles with manual 29.09.2014.pdf
– transmission
– MODEL 447.### ## as of 002621 with ENGINE 651 with TRANSMISSION 711.6
– with CODE GE1 (6-speed manual transmission TSG 380)
– MODEL 639.### ## as of 889319 with ENGINE 651 with TRANSMISSION 711.6
– with CODE GD8 (6-speed ECO Gear 360 manual transmission)
– MODEL 906 with ENGINE 651 with TRANSMISSION 711.6
– We would like to inform you that a changeover to low-friction oil