27-001 Installation survey test and pressure data.pdf
– Survey of transmission/model
– Transmission Installed in model
– 722.329 210.055
27-001 Installation survey test and pressure values of the basic and national.pdf
– Installation survey – transmission-model
– Transmission Model Transmission Model
– 722.400 201.024 722.425 202.120
27-001 Installation survey test and pressure values-.pdf
– Transmission Installed in model Standard implementation
– 722.400 201.024 effective start of production
27-002 Transmission ratios-.pdf
– 27-002 Transmission ratios
– Transmission diagram
– P27-0118-57A
27-002 Transmission ratios.pdf
– 27-002 Transmission ratios
– Transmission ratios
– Gear Ratio Actuated or effective shift Transmission ratio
– elements
27-004 Installation survey bottom cover – intermediate plate – gasket.pdf
27-006 Function of temperature- and boost pressure-dependent vacuum.pdf
– the central connection (VAC) of the pressure The temperature-dependent transmission control
– amplifier and controlled vacuum exists at the by the 50° temperature switch (S25/6) and the
– connection (VCV). automatic transmission pressure amplifier
– switchover valve (Y29) no longer applies (refer to
– The automatic transmission pressure amplifier the boost pressure influence is already effective
– switchover valve (Y29) is connected to ground via at the pressure amplifier when the engine is cold.
– a temperature switch; the valve operates the 2 – 3 The transmission cold comfort circuit is controlled
– connection. by a measure in the control valve body.
27-740 Adjusting and testing shift lock.pdf
AH27.00-S-1000-01PS General information on repair work on Topical note.pdf
– transmission
– Transmission 700.4 in model 190, 197
– Transmission 722.9 in model 447
– with code ZG2 (Permanent all-wheel drive)
– Transmission 722.9 in model 470, 471
– Transmission 722.96/97
– Transmission 725.0 in model 447, 448
– Transmission 725.0 in model 907
– Absolute cleanliness must be ensured when working on the
– transmission. Thoroughly clean area around the separating point before opening the hydraulic system. Use only lint-free cleaning cloths For repairs always wear oil-resistant, fiber-free gloves which are lined
– with rubber. Store transmission component parts in clean
– surroundings. Here it is recommended that you cover the component parts or store them in a clean plastic box with cover.Even the smallest foreign objects in the hydraulic components will lead to malfunctions and total failure of the transmission.
– Output shaft Transmission 722.9 in model 447
– Ring gear with code ZG2 (Permanent all-wheel drive)
– Needle roller bearing Transmission 722.96/97
– The transfer case cannot be replaced separately, it must be replaced Planet carrier
AH27.19-P-0001-01NKB Notes on automatic transmission.pdf
– AH27.19-P-0001-01NKB Notes on automatic transmission
– Transmission 700.42
– Transmission 700.750 in model 910
– Transmission 700.770 in model 470, 471
– Transmission 722.3/4/5/6/8/9
– Transmission 722.6 in model 636, 639
– Transmission 722.6 in model 902.6, 903.6, 904.6, 905.6
– Transmission 722.6 in model 906.1/2/6/7
– Transmission 722.9 in model 906, 907
– Transmission 723.3 in model 668, 670Transmission 723.6 in model 949, 950.5/6, 952.6, 957.38/5/6
– Transmission 723.6 in model 956, 963
– Transmission 723.6 in model 967
– Transmission 723.6 in model 970, 972, 975, 976
– Transmission 723.68
– Transmission 724.0/1/2
– Transmission 725.0 in model 907
– Transmission 725.0/1
– Transmission 725.0
– Absolute cleanliness is essential when working on the transmission. The transmission components should be stored in clean surrou ndings.
– Before opening the hydraulic circuit, thoroughly clean the area Here we recommend covering the components or storing them in a surrounding the separation point. Only lint-free cleaning cloths may be clean plastic box with a cover.used. Even the smallest dirt particles in the hydraulic components can lead to malfunctions and a total failure of the transmission.
– For repairs always wear oil-resistant, fiber-free gloves which are lined
– Only on transmission 700.750 in model 910, transmission 722.6 in Only on transmission 725.0 in model 907
– model 636, 639, transmission 722.6 in model 902.6, 903.6, 904.6, The hot measuring range on an automatic transmission at operat ing
AP27.00-D-2702C Automatic transmission fluid and oil filter change 10.07.2019.pdf
– AP27.00-D-2702C Automatic transmission fluid and oil filter change 10.07.2019
– Transmission 722.680/682/683/685/686 in model 639
– Transmission 722.681 in model 902.6, 903.6, 904.6, 905.6
– Transmission 722.685 in model 636
– 1 Oil filter
AP27.00-D-2702H Automatic transmission fluid and oil filter change 10.07.2019.pdf
– AP27.00-D-2702H Automatic transmission fluid and oil filter change 10.07.2019
– Transmission 722.683 in model 906.1/2/6/7
– Transmission 722.684 in model 906.1/2/6/7
– Transmission 722.685 in model 906.1/2/6/7
– Transmission 722.686 in model 906.1/2/6/7
– 1 Oil filter
AP27.00-D-2702HA Automatic transmission fluid and oil filter change 10.07.2019.pdf
– AP27.00-D-2702HA Automatic transmission fluid and oil filter change 10.07.2019
– Transmission 722.9 in model 906.1/2/6/7
– Modification notes
– 08.11.2018 Automatic transmission fluid ATF Transmission 722.9 BF27.00-N-1001-01A
– N27.10-2026-09
AP27.00-S-2702E Automatic transmission fluid and oil filter change 12.09.2017.pdf
– AP27.00-S-2702E Automatic transmission fluid and oil filter change 12.09.2017
– Transmission 722.9 in model 447
– Transmission 722.9 in model 448
– S27.00-4511-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
AR03.30-D-8003WE Remove install clutch plate 21.12.11.pdf
– ENGINES 651.955 /956 /957 in MODEL 906 with TRANSMISSION 722.686 /9
– D15.30-1116-08
AR03.30-P-8001CW Remove install flywheel drive plate 10.05.2016.pdf
– 1 Remove the transmission Transmission 722.9 in model 207 with engine AR27.10-P-0500CV
– 271
– Transmission 711.6 in model 172 with engine AR26.10-P-0020V
– Transmission 722.9 in model 172 with engine AR27.10-P-0500W
– Transmission 711.6 in model 204 with engine AR26.10-P-0020SA
– Transmission 711.6 in model 207 with engine AR26.10-P-0020CWA
– Transmission 716.6 in model 204, 207 with AR26.10-P-0020CW
– engine 271
– Transmission 722.6 in model 204.0/2/3 with AR27.10-P-0500CW
– up to model year 2012Transmission 722.6 in model 207 with engine 271
– Transmission 722.997 in model 204 with AR27.10-P-0500CWA
AR22.10-D-1170SD Remove install rear engine cross member 16.6.10.pdf
– 1 Rear engine crossmember 3 Transmission jack 5 Transmission2 Bolts 4 Engine mount 6 Bolts
– Remove/install
– 2 Lift transmission (5) with the transmission jack In the case of transmission 722.6, the
– (3) and transmission plate until engine mount transmission jack (3) with transmission plate
– (4) is relieved may only be placed on the outer edges of the
– transmission oil pan into to avoid damaging the transmission oil pan and underlying components.
– Underlay with suitable wooden blocks.
– Transmission jack 0.5 t
– gotis://H_00.10_01.0
– Passenger car transmission platform
– gotis://A_25/35/49_02.0
AR22.10-D-1170WE Remove install rear engine cross member 21.12.11.pdf
– Shown on model 906 with transmission 722.6
– 1 Transmission jack
– 2 Wooden block3 Oil pan
– transmission 722.6
– 4 Engine crossmember 6 Screw/bolts 8 Rear engine mount
AR27.00-D-0101A Inspect ATF level in automatic transmission add ATF if necessary 10.2.12.pdf
– AR27.00-D-0101A Inspect ATF level in automatic transmission, add ATF if necessary 10.2.12
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6 with CODE (G40) Automatic transmission
– TRANSMISSION 722.681 in MODEL WD1, WD2, WD3, WD6, WD7, XD1, XD2, XD3, XD4, XD5, XD6, XD7, YD1, YD2, YD3, YD4,
– YD5, YD6, YD7
– 10.2.12 Value modified: ATF liquid transmission oil, Specifications *BF27.00-N-1001-01A
– for Operating Fluids
– Adding transmission oil
– 1 Remove locking pin (93a) To do this, shear off the plate of the
– 3 Fill with transmission oil The vehicle must be horizontal.
– When refilling or following an oil change,
– pour in approx. 5 l of transmission oil before
– starting the engine.
AR27.00-D-0101WE Check oil level in automatic transmission and add oil if necessary 18.07.2019.pdf
– AR27.00-D-0101WE Check oil level in automatic transmission and add oil if necessary 18.07.2019
– Transmission 722.9 in model 906
– Transmission with guide tube for oil dipstick
– Modification notes
– 08.11.2018 Automatic transmission fluid ATF Transmission 722.9 BF27.00-N-1001-01A
– 1 Locking pin
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Check
AR27.00-D-0200-01B Drain transmission oil from torque converter.pdf
– AR27.00-D-0200-01B Drain transmission oil from torque converter
– and transmission
– Risk of injury Wear protective gloves, protective clothing Caution to skin and eyes due to AS00.40-Z-0001-01A
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Transmission 722.9 in model 906
– Modification notes
– Complete automatic transmission
– Number Designation Transmission 722.9
AR27.00-D-0200-01TS Drain transmission oil from torque converter.pdf
– AR27.00-D-0200-01TS Drain transmission oil from torque converter
– and transmission
– Risk of injury Wear protective gloves, protective clothing Caution to skin and eyes due to AS00.40-Z-0001-01A
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Model 907 with transmission 722.9
– Torque converter
– Number Designation Transmission 722.9
– BA27.20-N-1001-01F Drain screw to torque converter M8 Nm 10
AR27.00-D-0270-01A Top up automatic transmission after repair.pdf
– AR27.00-D-0270-01A Top up automatic transmission after repair
– work or maintenance with automatic
– transmission fluid
– Risk of accident Secure vehicle to prevent it from moving Danger! caused by vehicle starting AS00.00-Z-0005-01A
– 10.2.12 Value modified: Automatic transmission fluid ATF, *BF27.00-N-1001-01A
– Specifications for Operating Fluids
– Automatic transmission
– Number Designation Transmission
– 722.683/684/
– BF27.00-N-1001-01A Automatic transmission Filling capacity, first filling Liters 7,1
– fluid ATF
AR27.00-D-0270-01B Top up automatic transmission after repair.pdf
– AR27.00-D-0270-01B Top up automatic transmission after repair
– work or maintenance with automatic
– transmission fluid
– Risk of accident Secure vehicle to prevent it from moving Danger! caused by vehicle starting AS00.00-Z-0005-01A
– 10.2.12 Value modified: Automatic transmission fluid ATF, *BF27.00-N-1001-01A
– Specifications for Operating Fluids
– Value modified: Automatic transmission fluid ATF, *BF27.00-N-1001-01C
– Specifications for Operating Fluids
– Automatic transmission
– Number Designation Model
– transmission
– 722.6
– BF27.00-N-1001-01C Automatic transmission Filling capacity, first filling Liters 7.8
– fluid ATF
AR27.00-D-0270TSR Fill automatic transmission with transmission oil 18.07.2019.pdf
– AR27.00-D-0270TSR Fill automatic transmission with transmission oil 18.07.2019
– Transmission 722.9 in model 907
– Modification notes
– 08.11.2018 Automatic transmission fluid ATF Transmission 722.9 BF27.00-N-1001-01A
– 1 Overflow pipe
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.00-D-0270WE Fill automatic transmission with transmission oil 18.07.2019.pdf
– AR27.00-D-0270WE Fill automatic transmission with transmission oil 18.07.2019
– Transmission 722.9 in model 906
– Transmission without guide tube for oil dipstick
– 2 Adapter
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
AR27.00-P-0100AC Check oil level in automatic transmission and correct if necessary 02.07.2020.pdf
– AR27.00-P-0100AC Check oil level in automatic transmission and correct if necessary 02.07.2020
– Transmission 722.6
– 93 Plug
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.00-P-0101GC Inspect ATF level in automatic transmission add ATF if necessary 14.12.09.pdf
– AR27.00-P-0101GC Inspect ATF level in automatic transmission, add ATF if necessary 14.12.09
– TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133
– TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109TRANSMISSION 722.702 in MODEL 168.035 /135
– TRANSMISSION 722.750 /751 in MODEL 414.700
– A 30 °C (87 °F)
– Adding transmission oil
– Risk of accident Secure vehicle to prevent it from moving by Danger! caused by vehicle starting AS00.00-Z-0005-01A
– 3 Fill with transmission oil The vehicle must be horizontal.
– Transmission oil (ATF) in accordance with BB00.40-P-0236-10A
– Specifications for Operating Fluids, sheet no.
AR27.00-S-0200-01PS Drain transmission oil from torque converter.pdf
– AR27.00-S-0200-01PS Drain transmission oil from torque converter
– and transmission
– Risk of injury Wear protective gloves, protective clothing Caution to skin and eyes due to AS00.40-Z-0001-01A
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Transmission 722.9 in model 470, 471 with engine 642
– Torque converter
– Number Designation Transmission 722.9
– BA27.20-N-1001-01B Drain screw to torque converter M8 Nm 10
AR27.00-S-0270E Fill automatic transmission with transmission oil 16.11.2018.pdf
– AR27.00-S-0270E Fill automatic transmission with transmission oil 16.11.2018
– Model 447, 448 with transmission 722.9
– Modification notes
– 08.11.2018 Automatic transmission fluid ATF Transmission 722.9 BF27.00-N-1001-01A
– 1 Overflow pipe
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Fill with transmission oil
– 1 Raise vehicle. AR00.60-S-1000E
AR27.00-S-0270PS Fill automatic transmission with transmission oil 20.12.2018.pdf
– AR27.00-S-0270PS Fill automatic transmission with transmission oil 20.12.2018
– Transmission 722.9 in model 470, 471 with engine 642
– Modification notes
– 08.11.2018 Automatic transmission fluid ATF Transmission 722.9 BF27.00-N-1001-01A
– 19.12.2018 Specifications for Operating Fluids for transmission fluid Step 6
– changed
AR27.10-D-0005TSR Remove install automatic transmission 18.07.2019.pdf
– AR27.10-D-0005TSR Remove/install automatic transmission 18.07.2019
– Model 907 with engine 642, 651 with transmission 722.9
– Modification notes
AR27.10-D-0400A Remove install oil pump 03.12.2013.pdf
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.683 in MODEL 906.1/2/6/7
– TRANSMISSION 722.684 in MODEL 906.1/2/6/7
– TRANSMISSION 722.685 in MODEL 906.1/2/6/7
– TRANSMISSION 722.686 in MODEL 906.1/2/6/7
– D27.10-1112-09
– 1 Remove automatic transmission Transmission 722.681 AR27.10-D-0502A
– Transmission 722.683/684/685/686 AR27.10-D-0502B
– 2 Remove torque converter housing (2) with AR27.50-D-0602A
– multidisk brake B1 (3) from transmission housing
– 3 Unscrew two opposite bolts (4) a few
AR27.10-D-0400TSR Remove install oil pump 18.07.2019.pdf
– Transmission 722.9 in model 907
– D27.50-1162-09
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
– 1 Remove automatic transmission. AR27.10-D-0005TSR
– 2 Remove transmission housing from torque AR27.50-D-0601TSR
– converter housing (4).
AR27.10-D-0502-01TS Remove install lines at automatic transmission.pdf
– AR27.10-D-0502-01TS Remove/install lines at automatic transmission
– Risk of injury Wear protective gloves, protective clothing Caution to skin and eyes due to AS00.40-Z-0001-01A
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Transmission 722.9 in model 907
– Transmission oil cooling
– Number Designation Transmission 722.9
– BA27.55-N-1002-01I Bolt, oil line to Banjo bolt Stage 1 Nm 5
– transmission housing
– ° Stage 2 90
– BA27.55-N-1004-01I Bolt, dual clamp to oil line Nm 8
AR27.10-D-0502-01W Remove install lines at automatic.pdf
– transmission
– Transmission oil cooling system
– Number Designation Trans-
– BA27.55-N-1002-01I Bolt, transmission oil line to transmission Banjo bolt Stage 1 Nm 5
– housing
AR27.10-D-0502A Remove install automatic transmission 15.2.12.pdf
– AR27.10-D-0502A Remove/install automatic transmission 15.2.12
– TRANSMISSION 722.681 in MODELS 902.6, 903.6, 904.6, 905.6 with CODE (G40) Automatic transmission
– TRANSMISSION 722.681 in MODEL WD1, WD2, WD3, WD6, WD7, XD1, XD2, XD3, XD4, XD5, XD6, XD7, YD1, YD2, YD3, YD4, YD5,
– YD6, YD7
– 9 Bolt, transmission mount
– 10 Upper bearing shell for transmission
– suspension
– 14 Nuts, transmission bearing
– 15 Bleed hose bracket
– A Bolt, transmission housing to engine
– flange
AR27.10-D-0502B Remove install automatic transmission 12.04.2016.pdf
– AR27.10-D-0502B Remove/install automatic transmission 12.04.2016
– Transmission 722.683 in model 906.1/2/6/7
– Transmission 722.684 in model 906.1/2/6/7
– Transmission 722.685 in model 906.1/2/6/7
– Transmission 722.686 in model 906.1/2/6/7
– Modification notes
– Shown on transmission 722.685 without all-wheel drive
– 1 Transmission 3 Exhaust bracket 5 Torsion bar bracket
– 2 Transmission crossmember 4 Catalytic converter
– Risk of death Danger ! caused by vehicle slipping or Align vehicle between vehicle lift columns and AS00.00-Z-0010-01A
AR27.10-D-0502W Remove install automatic transmission 18.07.2019.pdf
– AR27.10-D-0502W Remove/install automatic transmission 18.07.2019
– Transmission 722.9 in model 906
– Modification notes
– 3 Automatic transmission
– 4 Support plate
AR27.10-D-0502WE Remove install automatic transmission 25.4.12.pdf
– AR27.10-D-0502WE Remove/install automatic transmission 25.4.12
– TRANSMISSION 722.686 in MODEL 906 with ENGINE 651.955 /956 /957
– D27.10-1141-09
– 1 Transmission 6 Torsion bar holder (with code (C40) 8 Wooden block
– Front axle stabilizer bar or with code 2 Screw 9 Rear engine crossmember
– (C45) Reinforced front axle stabilizer 3 Transmission platform 10 Bracket
– bar) 4 Transmission jack 11 Nut
– 7 Timing case 5 Tensioning strap 12 Bolts
– 9.2.12 Value changed: Automatic transmission fluid (ATF), *BF27.00-N-1001-01A
– Specifications for Operating Fluids
– 6 Drain transmission oil out of torque converter AR27.00-D-0200-01A Installation: Replace sealing rings.
– and transmission (1) and screw oil drain
– screws back in again
AR27.10-D-7030H Remove install automatic transmission oil pan 18.07.2019.pdf
– AR27.10-D-7030H Remove/install automatic transmission oil pan 18.07.2019
– Transmission 722.683 in model 906.1/2/6/7
– Transmission 722.684 in model 906.1/2/6/7
– Transmission 722.685 in model 906.1/2/6/7
– Transmission 722.686 in model 906.1/2/6/7
– Modification notes
– 08.11.2013 “Fill transmission oil” added. Operation step 12
– 20.11.2013 “Lower the vehicle” added. Operation step 13
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Raise the vehicle on lifting platform AR00.60-D-1000H
– Drain transmission oil
– 2 Remove oil pan drain screw (5)
AR27.10-D-7030WE Remove install automatic transmission oil pan 06.03.2020.pdf
– AR27.10-D-7030WE Remove/install automatic transmission oil pan 06.03.2020
– Transmission 722.9 in model 906
– Modification notes
– 1 Transmission housing 3 Overflow pipe 5 Seal
– 2 Bolts 4 Oil pan 6 Sprag
AR27.10-D-7031TSR Remove install automatic transmission oil pan 06.03.2020.pdf
– AR27.10-D-7031TSR Remove/install automatic transmission oil pan 06.03.2020
– Transmission 722.9 in model 907
– D27.10-1145-09
– 1 Transmission housing 3 Overflow pipe 5 Seal
– 2 Bolts 4 Oil pan 6 Sprag
AR27.10-S-0400S Remove install oil pump 18.07.2019.pdf
– Transmission 722.6 in model 636, 639
– Modification notes
– 09.02.2012 Value changed: Automatic transmission fluid (ATF), BF27.00-N-1001-01C
– Specifications for Operating Fluids
– 1 Transmission housing
– 2 Torque converter housing
AR27.10-S-0500E Remove install transmission with torque converter 29.01.2020.pdf
– AR27.10-S-0500E Remove/install transmission with torque converter 29.01.2020
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– Modification notes
AR27.10-S-0500SD Remove install transmission with torque converter 15.2.12.pdf
– AR27.10-S-0500SD Remove/install transmission with torque converter 15.2.12
– TRANSMISSION 722.6 in MODEL 639 with ENGINE 646
– N27.10-2019-09
AR27.10-S-0500SE Remove install transmission with torque converter 16.12.11.pdf
– AR27.10-S-0500SE Remove/install transmission with torque converter 16.12.11
– TRANSMISSION 722.6 in MODEL 639 with ENGINE 642
– Shown on engine 642.9
– transmission
– 3 Remove starter from transmission housing AR15.30-S-7100SE Do not disconnect electric cables.
– 4 Disconnect plug-in connector from electronic AR27.10-S-0500-01SV
– transmission control
– 5 Detach selector lever cable (1) from bracket Remove cable tie
AR27.10-S-0500SH Remove install transmission with torque converter 16.12.11.pdf
– AR27.10-S-0500SH Remove/install transmission with torque converter 16.12.11
– TRANSMISSION 722.6 in MODEL 636, 639 with ENGINE 272
– 1 Exhaust bracket
– 5 Automatic transmission
– S27.10-4518-06
– 4 Detach oil line of transmission cooling on AR27.55-S-0600SH Do not detach oil line on oil cooler.
– alternator
AR27.10-S-0500SJ Remove install transmission with torque converter 21.07.2016.pdf
– AR27.10-S-0500SJ Remove/install transmission with torque converter 21.07.2016
– Transmission 722.6 in model 639 with engine 651
– S27.10-4520-09
AR27.10-S-0500SV Remove install transmission with torque converter 15.2.12.pdf
– AR27.10-S-0500SV Remove/install transmission with torque converter 15.2.12
– MODEL 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815 with ENGINE 112.951 /976
– 3 Remove transmission oil filler pipe AR27.10-S-7010SV
– 4 Remove complete exhaust system AR49.10-S-7000SV
AR27.10-S-0510S Disassemble assemble transmission 21.4.09.pdf
– AR27.10-S-0510S Disassemble, assemble transmission 21.4.09
– TRANSMISSION 722.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– N27.10-2021-08
– 2 Transmission housing 6 Multi-disk brake B2
– 3 Drive shaft with clutch K2 and front gear set 7 Park pawl gear4 Output shaft with center and rear gear set 8 Electrohydraulic control unit
– 1 Detach transmission housing (2) from torque AR27.50-S-0601S
– converter housing (1)
AR27.10-S-7010SD Remove install oil filler pipe for automatic transmission 5.8.10.pdf
– AR27.10-S-7010SD Remove/install oil filler pipe for automatic transmission 5.8.10
– TRANSMISSION 722.6 in MODEL 639 with ENGINE 646
– Shown on vehicle as of vehicle
– 4 Transmission housing
– 5 Screw
AR27.10-S-7010SJ Remove install filler pipe for automatic transmission 04.09.2018.pdf
– AR27.10-S-7010SJ Remove/install filler pipe for automatic transmission 04.09.2018
– Transmission 722.6 in model 639 with engine 651
– S27.10-4519-09
AR27.10-S-7010SV Remove install oil filler pipe for automatic transmission 10.11.09.pdf
– AR27.10-S-7010SV Remove/install oil filler pipe for automatic transmission 10.11.09
– MODEL 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815 with ENGINE 112.951 /976
– 17 Transmission housing
– 19 Oil filler pipe
AR27.10-S-7030E Remove install automatic transmission oil pan 04.02.2016.pdf
– AR27.10-S-7030E Remove/install automatic transmission oil pan 04.02.2016
– Model 447, 448 with transmission 722.9
– S27.00-4511-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– Automatic transmission – oil and filter change AP27.00-S-2702E
– Do not drain oil from the torque converter.
– Model 447, 448 with transmission 722.9
– with code MJ8 (ECO start/stop function)
AR27.10-S-7030S Remove install automatic transmission oil pan 18.07.2019.pdf
– AR27.10-S-7030S Remove/install automatic transmission oil pan 18.07.2019
– Transmission 722.6 in model 636, 639
– Modification notes
– 09.02.2012 Value changed: Automatic transmission fluid (ATF), BF27.00-N-1001-01C
– Specifications for Operating Fluids
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Lift/jack up vehicle AR00.60-S-1000S
AR27.10-S-7031PS Remove install automatic transmission oil pan 06.03.2020.pdf
– AR27.10-S-7031PS Remove/install automatic transmission oil pan 06.03.2020
– Transmission 722.9 in model 470, 471 with engine 642
– D27.10-1145-09
– 1 Transmission housing 4 Oil pan 6 Sprag
– 2 Bolts
AR27.19-D-0200-01TSR Insert selector valve into driver of detent plate.pdf
– Transmission 722.9 in model 907
– 1 Align selector valve mount (1) with driver (2a) of detent plate (2) and insert
– controller unit (3) into transmission housing.
– The selector valve (1) of the controller unit (3) must latch into the driver (2a)
AR27.19-D-0200TSR Remove install electrohydraulic controller unit transmission installed 06.03.2020.pdf
– AR27.19-D-0200TSR Remove/install electrohydraulic controller unit (transmission installed) 06.03.2020
– Transmission 722.9 in model 907
– D27.19-1163-09
– 3 Transmission housing 7 Selector valve 10 O-rings4 Oil guide pipe
– Risk of death Danger caused by vehicle slipping or Align vehicle between vehicle lift columns and AS00.00-Z-0010-01A
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.19-D-0200WE Remove install electrohydraulic controller unit transmission installed 06.03.2020.pdf
– AR27.19-D-0200WE Remove/install electrohydraulic controller unit (transmission installed) 06.03.2020
– Transmission 722.9 in model 906
– D27.19-1151-09
– 1 Transmission housing 5 Oil filter 8 Detent plate
– 2 Electrical connector 6 Oil pan 9 Bolts
AR27.19-D-0210A Remove install electrohydraulic controller unit transmission removed 2.12.11.pdf
– AR27.19-D-0210A Remove/install electrohydraulic controller unit (transmission removed) 2.12.11
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.681 in MODEL WD1, WD2, WD3, WD6, WD7, XD1, XD2, XD3, XD4, XD5, XD6, XD7, YD1, YD2, YD3, YD4,
– YD5, YD6, YD7
– TRANSMISSION 722.683 /684 /685 /686 in MODEL 906
– 1 Screw
AR27.19-D-0212TSR Remove install control solenoid valves of electric controller unit 14.07.2019.pdf
– Transmission 722.9 in model 907
– D27.19-1166-09
AR27.19-D-0220A Disassemble and assemble electrohydraulic controller unit 03.12.2013.pdf
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.683 in MODEL 906.1/2/6/7
– TRANSMISSION 722.684 in MODEL 906.1/2/6/7
– TRANSMISSION 722.685 in MODEL 906.1/2/6/7
– TRANSMISSION 722.686 in MODEL 906.1/2/6/7
– Modification notes
AR27.19-D-0220TSR Disassemble and assemble electrohydraulic controller unit 06.03.2020.pdf
– Transmission 722.9 in model 907
– D27.19-1166-09
AR27.19-D-0220WE Disassemble and assemble electrohydraulic controller unit 21.12.11.pdf
– TRANSMISSION 722.9 in MODEL 906
– P27.19-2476-09
AR27.19-D-0550TS Remove install intelligent servo module 19.04.2018.pdf
– Model 907 with transmission 722.9
– D27.19-1168-08
– 1 Shift automatic transmission to position “N”.
– 2 Release parking brake.
AR27.19-D-0750-02TS Disconnect connect electrical connector on.pdf
– automatic transmission
– Risk of injury . Skin or eye injuries may result Wear protective gloves, protective clothing AS00.00-Z-0002-01A Warning
– Transmission 722.9 in model 907
– Housing
– Number Designation Transmission 722.9
– BA27.40-N-1007-01I Bolt, heat shield to transmission housing Nm 9
AR27.19-S-0200E Remove install electrohydraulic controller unit transmission installed 18.04.2016.pdf
– AR27.19-S-0200E Remove/install electrohydraulic controller unit (transmission installed) 18.04.2016
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– S27.19-4528-09
– 1 Transmission housing 4e Transmission plug 82 Detent plate
– 2 Oil guide pipe 4s Bolt N15/11 Fully integrated transmission
– control (VGS) electric controller unit
AR27.19-S-0200S Remove install electrohydraulic controller unit transmission installed 25.10.10.pdf
– AR27.19-S-0200S Remove/install electrohydraulic controller unit (transmission installed) 25.10.10
– TRANSMISSION 722.6 in MODEL 636, 639
– S27.10-4509-09
– transmission
– 2 Remove oil filter (2) downwards Installation: Replace oil filter (2).
AR27.19-S-0212E Remove install control solenoid valves of electric controller unit 16.11.2018.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– S27.19-4527-09
– 2 Leaf spring N15/11n4 Fully integrated transmission N15/11y5 Multidisk brake control
– control (VGS) control unit solenoid valve B1
AR27.19-S-0220E Disassemble and assemble electrohydraulic controller unit 16.11.2018.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– S27.19-4526-09
– 2 Leaf spring N15/11n4 Fully integrated transmission N15/11y6 Multidisk brake control
– control (VGS) control unit solenoid valve B2
AR27.19-S-0220S Disassemble and assemble electrohydraulic control unit 22.4.09.pdf
– TRANSMISSION 722.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– 15 Caps
AR27.19-S-0550E Remove install intelligent servo module 04.02.2016.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– S27.19-4523-08
AR27.20-S-0050S Remove install torque converter 25.10.10.pdf
– TRANSMISSION 722.6 in MODEL 636, 639
– N27.20-2024-09
– Shown on engine 646 1 Automatic transmission 2 Torque converter
– Modification notes
– 1 Remove automatic transmission (1) with Engine 646 AR27.10-S-0500SD
– torque converter (2)
AR27.20-S-0200-03E Drain gear oil from torque converter.pdf
– Model 447, 448 with transmission 722.9
– Torque converter
– Number Designation Transmission 722.9
– BA27.20-N-1001-01B Drain plug to torque converter M8 Nm 10
– Model 447, 448 with transmission 722.9 Model 447 with engine 651
– with code MJ8 (ECO start/stop function) The special tools counterholder 651 589 00 40 00 or
AR27.30-D-0651WE Remove install auxiliary oil pump for automatic transmission 06.03.2020.pdf
– AR27.30-D-0651WE Remove/install auxiliary oil pump for automatic transmission 06.03.2020
– Transmission 722.9 in model 906
– with code MJ7 (ECO start/stop function)
– with code MJ8 (ECO start/stop function)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.30-S-0651E Remove install auxiliary oil pump for automatic transmission 06.03.2020.pdf
– AR27.30-S-0651E Remove/install auxiliary oil pump for automatic transmission 06.03.2020
– Model 447, 448 with transmission 722.9
– with code MJ8 (ECO start/stop function)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.30-S-4970E Remove install radial shaft sealing ring on front transmission cover 27.01.2020.pdf
– AR27.30-S-4970E Remove/install radial shaft sealing ring on front transmission cover 27.01.2020
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– Modification notes
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
– 1 Remove transmission. AR27.10-S-0500E
– 2 Fasten transmission onto assembly stand. AR27.10-S-0600-01E
– *116589065900 Assembly stand
AR27.30-S-4970S Remove install radial shaft sealing ring on front transmission cover 25.10.10.pdf
– AR27.30-S-4970S Remove/install radial shaft sealing ring on front transmission cover 25.10.10
– TRANSMISSION 722.6 in MODEL 636, 639
– 1 Radial shaft seal
– 1 Remove transmission with torque converter Engine 646 AR27.10-S-0500SD
– Engine 642 AR27.10-S-0500SE
– damage to the transmission.
– Install
AR27.35-S-0350S Dismantle and assemble shift plate 25.5.10.pdf
– TRANSMISSION 722.6 in MODEL 636, 639
– 70 Strainers
AR27.40-D-0003TSC Detach attach transmission housing of torque converter housing 12.02.2020.pdf
– AR27.40-D-0003TSC Detach/attach transmission housing of torque converter housing 12.02.2020
– Transmission 725.0 in model 907
– Modification notes
– 1 Transmission housing
– 4 Pipes
AR27.40-D-0205B Remove install radial shaft sealing ring on output flange 12.04.2019.pdf
– Transmission 722.681 in model 902.6, 903.6, 904.6, 905.6
– Transmission 722.683/684/685 in model 906
– except code ZG1 (Engageable all-wheel drive)
– Transmission 722.686 in model 906.1/2/6/7
– 22.09.2015 Propeller shaft to transmission Model 906 BA41.10-N-1001-01B
– D27.40-1103-09
– Shown on transmission 722.681
– 1 Thrust plate 4 Collar nut 7 Check strap
AR27.40-D-0205C Remove install radial shaft sealing ring on output flange 12.04.2019.pdf
– Transmission 722.683/684/685 in model 906
– with code ZG1 (Engageable all-wheel drive)
– with code ZG3 (Engageable all-wheel drive with gear reduction)
– Transmission 722.686 in model 906.1/2/6/7
AR27.40-D-0205WE Remove install radial shaft sealing ring on output flange 14.07.2019.pdf
– Transmission 722.9 in model 906
– D27.40-1111-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
– Collect escaping transmission oil.
– *BA27.50-N-1001-01C Collar nut, output flange to output shaft
AR27.40-D-0206TSR Remove install radial shaft sealing ring at output side 14.07.2019.pdf
– Transmission 722.9 in model 907
– except code ZG1 (Engageable all-wheel drive)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
AR27.40-D-0206TSX Remove install radial shaft sealing ring at output side 14.07.2019.pdf
– Model 907 with transmission 722.9
– with code ZG1 (Engageable all-wheel drive)
– with code ZG3 (Engageable all-wheel drive with gear reduction)
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
AR27.40-D-0220WE Remove install shift shaft radial shaft sealing ring 21.12.11.pdf
– TRANSMISSION 722.9 in MODEL 906
– D27.40-1112-08
– 3 Detent plate 6 Detent plate spring element 1 Transmission housing
– 4 Detent plate clamp bolt 7 Radial shaft seal 2 Shift shaft
– 3 Clean transmission housing (1) around shift Cleaner from package *BR00.45-Z-1028-04A
– shaft (2) and radial shaft sealing ring (7)
– 4 Remove automatic transmission oil pan AR27.10-D-7030WE
– 5 Remove bolt (5) and remove spring element
– pull shift shaft (2) out of transmission housing (1)
– 7 Remove radial shaft seal (7) using suitable Make sure that the contact surface in the
– tool transmission housing (1) is not damaged.
– Leaks may occur otherwise.
AR27.40-D-0221TSR Remove install radial shaft sealing ring of gearshift shaft 06.03.2020.pdf
– Transmission 722.9 in model 907
– P27.40-2055-08
– 1 Transmission housing 20 Radial shaft sealing ring 82a Detent plate clamp bolt
– 16 Detent plate spring element 40 Shift shaft
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– 2 Clean transmission housing (1) in area of Assembly cleaner *BR00.45-Z-1028-04A
– gearshift shaft (40) and radial shaft sealing ring (20).
AR27.40-D-0300A Remove install oil pump radial shaft sealing ring 27.4.09.pdf
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.681 in MODEL WD1, WD2, WD3, WD6, WD7, XD1, XD2, XD3, XD4, XD5, XD6, XD7, YD1, YD2, YD3, YD4,
– YD5, YD6, YD7
– TRANSMISSION 722.683 in MODEL 906.1 /2 /6 /7TRANSMISSION 722.684 in MODEL 906.1 /2 /6 /7
– TRANSMISSION 722.685 in MODEL 906.1 /2 /6 /7
– TRANSMISSION 722.686 in MODEL 906.1 /2 /6 /7
– 1 Radial shaft seal
– 1 Remove automatic transmission Transmission 722.681 AR27.10-D-0502A
– Transmission 722.683/684/685 AR27.10-D-0502B
– Transmission 722.686 AR27.10-D-0502WE
– 2 Remove torque converter Transmission 722.681 AR27.20-D-0500-01B
– *126589016200
AR27.40-D-0300WE Remove install oil pump radial shaft sealing ring 21.12.11.pdf
– TRANSMISSION 722.9 in MODEL 906
– Torque converter removed
– 2 Oil pump housing3 Transmission
– P27.57-2004-06
– resulting in transmission (3) damage or destruction.
– Cleaning
AR27.40-D-0301TSR Remove install oil pump radial shaft sealing ring 14.07.2019.pdf
– Transmission 722.9 in model 907
– 01 Drift
– 3 Automatic transmission
– P27.57-2004-06
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– 1 Remove automatic transmission (3). AR27.10-D-0005TSR
– 2 Remove torque converter. AR27.20-D-0500-01TS
AR27.40-S-0003EA Detach attach transmission housing of torque converter housing 25.08.2020.pdf
– AR27.40-S-0003EA Detach/attach transmission housing of torque converter housing 25.08.2020
– Model 447 with transmission 725.0
– except code ZG2 (Permanent all-wheel drive)
– Model 448 with transmission 725.0
– Modification notes
– 1 Transmission housing
– 4 Oil guide pipe5 Screw
AR27.40-S-0003EB Detach attach transmission housing of torque converter housing 19.08.2020.pdf
– AR27.40-S-0003EB Detach/attach transmission housing of torque converter housing 19.08.2020
– Transmission 725.0 in model 447
– with code ZG2 (Permanent all-wheel drive)
– 1 Transmission housing
– 4 Torque converter housing ventilation
AR27.40-S-0205E Remove install radial shaft sealing ring on output flange 12.04.2019.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– D27.40-1111-09
– Collect escaping transmission oil.
– *BA27.50-N-1001-01C Collar nut, output flange to output shaft
AR27.40-S-0220E Remove install shift shaft radial shaft sealing ring 06.03.2020.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– P27.40-2055-08
– 1 Transmission housing 20 Radial shaft sealing ring 82a Detent plate clamp bolt16 Detent plate spring element 40 Shift shaft
– Remove
– 2 Clean transmission housing (1) in area of shift Assembly cleaner *BR00.45-Z-1028-04A
– shaft (40) and radial shaft sealing ring (20)
– transmission housing (1) is not damaged.Leaks can occur otherwise.
– Check
AR27.40-S-0510S Disassemble assemble transmission housing 21.4.09.pdf
– AR27.40-S-0510S Disassemble/assemble transmission housing 21.4.09
– TRANSMISSION 722.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– 2 Transmission housing
– 5 Disk pack B3
AR27.50-D-0601A Detach attach transmission housing on torque converter housing. 03.12.2013.pdf
– AR27.50-D-0601A Detach/attach transmission housing on torque converter housing. 03.12.2013
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.683 in MODEL 906.1/2/6/7
– TRANSMISSION 722.684 in MODEL 906.1/2/6/7
– TRANSMISSION 722.685 in MODEL 906.1/2/6/7
– TRANSMISSION 722.686 in MODEL 906.1/2/6/7
– D27.50-1104-09
– 4 Transmission housing 8 Thrust plate 12 Teflon rings
– Remove
– 1 Remove automatic transmission TRANSMISSION 722.681 AR27.10-D-0502A
– TRANSMISSION 722.683 AR27.10-D-0502B
– TRANSMISSION 722.684TRANSMISSION 722.685TRANSMISSION 722.686 in MODEL
– 906.1/2/6/7
AR27.50-D-0601TSR Detach attach transmission housing on torque converter housing. 14.07.2019.pdf
– AR27.50-D-0601TSR Detach/attach transmission housing on torque converter housing. 14.07.2019
– Transmission 722.9 in model 907
– D27.50-A000-09
– Shown except code ZG1 (All-wheel drive, engageable) and except code ZG3 (Engageable all-wheel drive with transmission ratio)
– 01 Support plate 6 Oil pan 11 Deep-groove ball bearing
– 3 Transmission housing 10 Radial shaft sealing ring N15/11 Fully integrated transmission
– control (VGS) electric controller unit
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
AR27.50-D-0601WE Detach attach transmission housing on torque converter housing. 21.12.11.pdf
– AR27.50-D-0601WE Detach/attach transmission housing on torque converter housing. 21.12.11
– TRANSMISSION 722.9 in MODEL 906
– D27.50-1161-09
– 2 Seal 8 Output flange 13 Multidisk brake B23 Transmission housing 9 Internal Torx bolts (2 each) 14 Internal Torx bolts (15 each)
– 5 Oil filter 10 Radial sealing ring
– 1 Remove automatic transmission AR27.10-D-0502W
– 2 Fasten transmission on assembly stand AR27.10-D-0600-01WE
– *116589065900 Assembly stand
AR27.50-D-0602A Remove install torque converter housing and multi-disk brake B1 from 03.12.2013.pdf
– transmission housing
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.683 in MODEL 906.1/2/6/7
– TRANSMISSION 722.684 in MODEL 906.1/2/6/7
– TRANSMISSION 722.685 in MODEL 906.1/2/6/7
– TRANSMISSION 722.686 in MODEL 906.1/2/6/7
– 1 Screw
– 4 Transmission housing
– D27.50-1136-06
– 1 Remove automatic transmission TRANSMISSION 722.681 in MODEL 902.6, AR27.10-D-0502A
– 903.6, 904.6, 905.6
– TRANSMISSION 722.683 in MODEL AR27.10-D-0502B
– 906.1/2/6/7TRANSMISSION 722.684 in MODEL
– 906.1/2/6/7
– TRANSMISSION 722.685 in MODEL 906.1/2/6/7TRANSMISSION 722.686 in MODEL 906.1/2/6/7
– 2 Put down transmission and oil pan
– 3 Remove torque converter TRANSMISSION 722.681 in MODEL 902.6,
AR27.50-D-0603A Disassemble the transmission into its main components 04.03.2015.pdf
– AR27.50-D-0603A Disassemble the transmission into its main components 04.03.2015
– Transmission 722.681 in model 902.6, 903.6, 904.6, 905.6
– Transmission 722.683 in model 906.1/2/6/7
– Transmission 722.684 in model 906.1/2/6/7
– Transmission 722.685 in model 906.1/2/6/7
– Transmission 722.686 in model 906.1/2/6/7
– D27.50-1108-09
AR27.50-D-0604A Remove install output shaft bearing 01.02.2016.pdf
– Transmission 722.681 in model 902.6, 903.6, 904.6, 905.6
– Transmission 722.683 in model 906.1/2/6/7
– Transmission 722.684 in model 906.1/2/6/7
– Transmission 722.685 in model 906.1/2/6/7
– Transmission 722.686 in model 906.1/2/6/7
– 1 Shim
– 1 Raise vehicle Transmission 722.681 in model 902.6, 903.6, AR00.60-D-1000A
– 904.6, 905.6
– Model 906.1/2/6/7 with transmission 722.683 AR00.60-D-1000H
– Model 906.1/2/6/7 with transmission 722.684
– Model 906.1/2/6/7 with transmission 722.685Model 906.1/2/6/7 with transmission 722.686
– 2.1 Remove propeller shaft to transfer case. Transmission 722.681 in model 903.6, 904.6
– with code ZG1 (Engageable all-wheel drive)
AR27.50-D-0610TSR Remove install main components of transmission 14.07.2019.pdf
– AR27.50-D-0610TSR Remove/install main components of transmission 14.07.2019
– Transmission 722.9 in model 907
– S27.00-4510-09
– 1 Transmission housing 33 Drive unit 55 Housing components
– 1w Torque converter housing 44 Output unit N15/11 Fully integrated transmission
– control (VGS) electric controller unit
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
– 1 Remove fully integrated transmission control AR27.19-D-0200TSR
– (VGS) electric controller unit (N15/11).
– 2 Remove transmission housing (1) from torque AR27.50-D-0601TSR
– converter housing (1w).
AR27.50-D-0610WE Remove install main components of transmission 18.07.2019.pdf
– AR27.50-D-0610WE Remove/install main components of transmission 18.07.2019
– Transmission 722.9 in model 906
– D27.00-1112-09
– 1 Transmission housing 44 Output unit
– 1w Torque converter housing 55 Housing components
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Remove electric controller unit (Y3/8) AR27.19-D-0200WE
– 2 Detach transmission housing (1) from torque AR27.50-D-0601WE
– converter housing (1w)
AR27.50-D-0611TSR Remove install K3 rear hollow shaft rear planet carrier and output shaft 14.07.2019.pdf
– Transmission 722.9 in model 907
– P27.00-2141-09
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
AR27.50-D-0611WE Remove install K3 rear hollow shaft rear planet carrier and output shaft 18.07.2019.pdf
– Transmission 722.9 in model 906
– P27.00-2141-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Detach transmission housing from torque AR27.50-D-0601WE
– converter housing (1w)
AR27.50-D-0612TSR Removing installing drive shaft with K2 front planet carrier internal plate carrier 14.07.2019.pdf
– Transmission 722.9 in model 907
– P27.00-2142-09
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
– Automatic transmission fluids (ATF) BB00.40-P-0236-15A
– (specification 236.15)
– Apply oil to transmission components before installation.Otherwise damage can occur during the
– startup phase when the transmission is being
AR27.50-D-0612WE Removing installing drive shaft with K2 front planet carrier internal plate carrier 18.07.2019.pdf
– Transmission 722.9 in model 906
– P27.00-2142-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Remove output unit AR27.50-D-0611WE
AR27.50-D-0617TSC Detach attach external plate carrier B08 on torque converter housing 14.07.2019.pdf
– Transmission 725.0 in model 907
– 2 Torque converter housing
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.50-D-0618TSC Remove install piston B08 14.07.2019.pdf
– Transmission 725.0 in model 907
– P27.50-2262-09
AR27.50-D-0619TSC Disassemble assemble multidisk clutch K27 14.07.2019.pdf
– Transmission 725.0 in model 907
– 1 K27 multiplate clutch
AR27.50-D-0620-02A Removing and installing output flange.pdf
– Transmission 722.681 in model 902.6, 903.6, 904.6, 905.6
– Transmission 722.683/684/685 in model 906
– except code ZG1 (Engageable all-wheel drive)
– Transmission 722.686 in model 906
– Number Designation Transmission TRANSMISSION
– 722.681 722.683/684/685/
AR27.50-D-0622TSC Disassemble assemble multidisk clutch K81 14.07.2019.pdf
– Transmission 725.0 in model 907
– P27.50-2211-08
AR27.50-D-0624TSC Remove install planetary gear set 2 and multidisk clutch K38 with ring gear 14.07.2019.pdf
– Transmission 725.0 in model 907
– 1 Planetary gear system 2
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
AR27.50-D-0721A Remove install multi-disk brake B1 and oil pump 03.12.2013.pdf
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.683 in MODEL 906.1/2/6/7
– TRANSMISSION 722.684 in MODEL 906.1/2/6/7
– TRANSMISSION 722.685 in MODEL 906.1/2/6/7
– TRANSMISSION 722.686 in MODEL 906.1/2/6/7
– D27.50-1126-09
– 1 Remove automatic transmission TRANSMISSION 722.681 in MODEL 902.6, AR27.10-D-0502A
– 903.6, 904.6, 905.6
– TRANSMISSION 722.683/684/685/686 in AR27.10-D-0502B
– MODEL 906.1/2/6/7
– multidisk brake B1 (4) from transmission
– housing
AR27.50-D-0721TSR Remove install multi-disk brake B1 and oil pump 18.07.2019.pdf
– Transmission 722.9 in model 907
– P27.00-2144-09
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.50-D-0721WE Remove install multi-disk brake B1 and oil pump 18.07.2019.pdf
– Transmission 722.9 in model 906
– P27.00-2144-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Remove drive unit AR27.50-D-0612WE
AR27.50-D-0781A Remove install multi-disk brake B2 disk pack B3 and park pawl gear 03.12.2013.pdf
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.683 in MODEL 906.1/2/6/7
– TRANSMISSION 722.684 in MODEL 906.1/2/6/7
– TRANSMISSION 722.685 in MODEL 906.1/2/6/7
– TRANSMISSION 722.686 in MODEL 906.1/2/6/7
– D27.50-1110-09
– Shown on transmission 722.681
– 1 Retaining ring (a different number of externally 9 Transmission housing
– toothed plates are fitted depending on
AR27.50-D-0782TSR Remove install clutch pack BR multidisk brake B2 and park pawl gear 18.07.2019.pdf
– Transmission 722.9 in model 907
– P27.00-2145-09
– 1 Transmission housing 5t Disk spring 6s Screw
– 5 Clutch pack BR 6 B2 multidisk brake 7 Park pawl gear
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– 1 Remove transmission housing (1) from torque AR27.50-D-0601TSR
– converter housing.
AR27.50-D-0782WE Remove install clutch pack BR multidisk brake B2 and park pawl gear 18.07.2019.pdf
– Transmission 722.9 in model 906
– P27.00-2145-09
– 1 Transmission housing 6 B2 multidisk brake
– 5 Clutch pack BR 6s Screw
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
– 1 Detach transmission housing (1) from torque AR27.50-D-0601WE
– converter housing
AR27.50-D-0810-01WE Check adjust axial play between shim and.pdf
AR27.50-D-0810A Disassemble assemble output shaft with center and rear gear set 21.07.2017.pdf
– Transmission 722.681 in model 902.6, 903.6, 904.6, 905.6
– Transmission 722.683 in model 906.1/2/6/7
– Transmission 722.684 in model 906.1/2/6/7
– Transmission 722.685 in model 906.1/2/6/7
– Transmission 722.686 in model 906.1/2/6/7
– D27.50-1158-09
– 1 Remove automatic transmission Transmission 722.681 in model 902.6, 903.6, AR27.10-D-0502A
– 904.6, 905.6
– Transmission 722.683/684/685/686 in model AR27.10-D-0502B
– 906.1/2/6/7
– 2 Remove transmission housing from torque AR27.50-D-0601A
– converter housing
AR27.50-D-0851TSR Dismantle and assemble rear tubular shaft 18.07.2019.pdf
– Transmission 722.9 in model 907
– 22a Axial needle roller bearing
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
AR27.50-D-0870B Disassemble assemble multi-disk brake B1 21.07.2017.pdf
– Transmission 722.681 ## as of 3947440 in model 902.6, 903.6, 904.6, 905.6
– Transmission 722.683 in model 906.1/2/6/7
– Transmission 722.684 in model 906.1/2/6/7
– Transmission 722.685 in model 906.1/2/6/7
– Transmission 722.686 in model 906.1/2/6/7
– D27.50-1145-09
– Shown on transmission 722.681
– 1 External plate carrier 6 Externally toothed plate 9 Retaining ring
AR27.50-D-0870TSR Disassemble assemble multi-disk brake B1 18.07.2019.pdf
– Transmission 722.9 in model 907
– S27.51-0001-09
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
AR27.50-D-0870WE Disassemble assemble multi-disk brake B1 18.07.2019.pdf
– Transmission 722.9 in model 906
– D27.51-1140-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Check thrust bearing (161) and bearing (162) Check the contact surfaces, thrust bearing
AR27.50-D-0880TSR Disassemble assemble multi-disk brake B2 18.07.2019.pdf
– Transmission 722.9 in model 907
– D27.51-1139-09
AR27.50-D-0880WE Disassemble assemble multi-disk brake B2 18.07.2019.pdf
– Transmission 722.9 in model 906
– D27.51-1139-09
AR27.50-D-0890TSR Disassemble assemble multi-disk brake B3 18.07.2019.pdf
– Transmission 722.9 in model 907
– P27.51-2033-09
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.50-D-0890WE Disassemble assemble multi-disk brake B3 18.07.2019.pdf
– Transmission 722.9 in model 906
– P27.51-2033-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Remove retaining ring (105s) and end disk
AR27.50-P-0620-02W Removing and installing output flange.pdf
– Transmission 722.6/9, 724.2
– Transmission 725.0/1
– Automatic transmission complete
– Number Designation Transmission
– 725.0/1
– Number Designation Transmission 724.2
– BA27.10-P-1014-04G Collar nut, output flange to output shaft Nm 200
– 722.55/6/9
AR27.50-S-0600-06E Measure end play between park pawl gear.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– Modification notes
– Number Designation Transmission 722.9
– BE27.50-N-1001-01B Axial play between park pawl gear and grooved ball bearing mm 0,2…0,4
AR27.50-S-0601E Detach attach transmission housing on torque converter housing. 18.04.2016.pdf
– AR27.50-S-0601E Detach/attach transmission housing on torque converter housing. 18.04.2016
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– Modification notes
– 2 Seal 9 Bolt N15/11 Fully integrated transmission
– control (VGS) electric controller unit
– 3 Transmission housing 10 Radial shaft sealing ring
– 5 Oil filter 11 Grooved ball bearing
AR27.50-S-0601S Detach attach transmission housing on torque converter housing. 25.10.10.pdf
– AR27.50-S-0601S Detach/attach transmission housing on torque converter housing. 25.10.10
– TRANSMISSION 722.6 in MODEL 636, 639
– D27.50-1104-09
– 4 Transmission housing 10 Output flange
– 5 Shim 11 Twelve-point collar nut6 Grooved ball bearing 12 Teflon rings
– 1 drain transmission oil from torque converter AR27.00-S-0200-01S
– and transmission
– *BA27.10-N-1014-04A
AR27.50-S-0610E Remove install main components of transmission 18.04.2016.pdf
– AR27.50-S-0610E Remove/install main components of transmission 18.04.2016
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– S27.00-4510-09
– 1 Transmission housing 33 Drive unit N15/11 Fully integrated transmission
– control (VGS) electric controller
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
– 1 Remove fully integrated transmission control AR27.19-S-0200E
– (VGS) electric controller unit (N15/11)
– 2 Detach transmission housing (1) from torque AR27.50-S-0601E
– converter housing (1w)
AR27.50-S-0610S Remove install main components of transmission 21.4.09.pdf
– AR27.50-S-0610S Remove/install main components of transmission 21.4.09
– TRANSMISSION 722.6 in MODEL 636, 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815
– N27.10-2021-08
– 2 Transmission housing 6 Multi-disk brake B2
– 3 Drive shaft with K2 clutch and front gear set 7 Park pawl gear4 Output shaft with center and rear gear set 8 Electrohydraulic control unit
– 1 Detach transmission housing (2) from torque AR27.50-S-0601S
– converter housing (1).
AR27.50-S-0611E Remove install K3 rear hollow shaft rear planet carrier and output shaft 16.11.2018.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– P27.00-2141-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
AR27.50-S-0617EA Detach attach external plate carrier B08 on torque converter housing 20.07.2020.pdf
– Transmission 725.0 in model 447, 448
– 2 Torque converter housing
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.50-S-0618EA Remove install piston B08 20.07.2020.pdf
– Transmission 725.0 in model 447, 448
– P27.50-2262-09
AR27.50-S-0619EA Disassemble assemble multidisk clutch K27 20.07.2020.pdf
– Transmission 725.0 in model 447, 448
– 1 K27 multiplate clutch
AR27.50-S-0620-02E Removing and installing output flange.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– Gear assembly
– Number Designation Transmission 722.9
– BA27.50-N-1001-01C Collar nut, output flange to output shaft Nm 200
AR27.50-S-0622EA Disassemble assemble multidisk clutch K81 20.07.2020.pdf
– Transmission 725.0 in model 447, 448
– P27.50-2211-08
AR27.50-S-0624EA Remove install planetary gear set 2 and multidisk clutch K38 with ring gear 20.07.2020.pdf
– Transmission 725.0 in model 447, 448
– 1 Planetary gear system 2
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– transmission
– Remove
AR27.50-S-0721E Remove install multi-disk brake B1 and oil pump 16.11.2018.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– P27.00-2144-09
AR27.50-S-0781S Remove install multi-disk brake B2 disk pack B3 and park pawl gear 25.5.10.pdf
– TRANSMISSION 722.6 in MODEL 636, 639
– N27.51-2004-09
– 2 Transmission housing 6 Multidisk brake B2
– 5 Disk pack B3 6s Bolts5s Snap ring 7 Park pawl gear
– 1 Detach transmission housing (2) from torque AR27.50-S-0601S
– converter housing.
AR27.50-S-0782E Remove install clutch pack BR multidisk brake B2 and park pawl gear 16.11.2018.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– P27.00-2145-09
– 1 Transmission housing 5t Disk spring 7 Park pawl gear
– 5 Clutch pack BR 6 B2 multidisk brake
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– 1 Remove transmission housing (1) from torque AR27.50-S-0601E
– converter housing.
AR27.50-S-0880-01E Assemble piston guide and external plate.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– Modification notes
– Number Designation Transmission 722.9
– BA27.40-N-1003-01I Bolt, multi-disk brake B2 to transmission Stage 1 Nm 10
– housing
AR27.50-S-0880E Disassemble assemble multi-disk brake B2 21.04.2016.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– Modification notes
AR27.50-S-4866S Remove install multi-disk brake B1 18.07.2019.pdf
– Transmission 722.6 in model 636, 639
– Modification notes
– 09.02.2012 Value changed: Automatic transmission fluid (ATF), BF27.00-N-1001-01C
– Specifications for Operating Fluids
– 1 Transmission housing
– 2 Torque converter housing
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Lift/jack up vehicle AR00.60-S-1000S
AR27.51-D-0550-04TSC Measure and adjust clearance of multidisk.pdf
– Transmission 725.0 in model 907
– Adjustment values for multidisk clutch/multidisk brake
– Number Designation Transmission 725.0
– BE27.51-P-1004-01E Clearance in multidisk Contact force for F1 N 600
– BE27.51-P-1005-01E Clearance in multidisk Contact force for F1 N 600
AR27.51-D-0560-03TSC Measure and adjust clearance of multidisk.pdf
– Transmission 725.0 in model 907
– Adjustment values for multidisk clutch/multidisk brake
– Number Designation Transmission 725.0
– BE27.51-P-1006-01E Clearance in multidisk Contact force for F1 N 1600
AR27.51-D-0800TSR Dismantling and assembling clutch K1 18.07.2019.pdf
– Transmission 722.9 in model 907
– P27.51-2027-08
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
AR27.51-D-0800WE Dismantling and assembling clutch K1 18.07.2019.pdf
– Transmission 722.9 in model 906
– P27.51-2027-08
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Remove axial bearing from outer plate carrier
AR27.51-D-0820TSR Disassemble assemble K2 clutch 18.07.2019.pdf
– Transmission 722.9 in model 907
– P27.51-2029-09
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
AR27.51-D-0820WE Disassemble assemble K2 clutch 18.07.2019.pdf
– Transmission 722.9 in model 906
– P27.51-2029-09
AR27.51-D-0825A Disassemble assemble drive shaft with K2 clutch and front gear set 21.07.2017.pdf
– Model 902.6, 903.6, 904.6, 905.6 with transmission 722.681
– Model 906.1/2/6/7 with transmission 722.683
– Model 906.1/2/6/7 with transmission 722.684
– Model 906.1/2/6/7 with transmission 722.685
– Model 906.1/2/6/7 with transmission 722.686
– D27.51-1128-09
– Shown on transmission 722.681
– 1 Needle roller bearing 9 Piston 17 External plate (2.8 mm) (a different
AR27.51-D-0830TSR Disassemble assemble K3 clutch 18.07.2019.pdf
– Transmission 722.9 in model 907
– P27.51-2030-09
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
AR27.51-D-0830WE Disassemble assemble K3 clutch 18.07.2019.pdf
– Transmission 722.9 in model 906
– P27.51-2030-09
– Notes on automatic transmission AH27.19-P-0001-01NKB
– 1 Remove retaining ring (105s) and end disk
AR27.51-D-7229TSR Measure and adjust clearance 18.07.2019.pdf
– Transmission 722.9 in model 907
– 105 End disk
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Measure
AR27.51-D-7230-01TSC Measure and adjust clearance of multidisk.pdf
– Transmission 725.0 in model 907
– Adjustment values for multidisk clutch/multidisk brake
– Number Designation Transmission 725.0
– BE27.51-P-1001-01E Clearance in multidisk Contact force for F1 N 500
– BE27.51-P-1002-01E Clearance in multidisk Contact force for F1 N 500
AR27.51-D-7230-02TSC Measure and adjust clearance of multidisk.pdf
– Transmission 725.0 in model 907
– Adjustment values for multidisk clutch/multidisk brake
– Number Designation Transmission 725.0
– BE27.51-P-1003-01E Clearance in multidisk Contact force for F1 N 600
AR27.51-S-0550-04EA Measure and adjust clearance of multidisk.pdf
– transmission
– Transmission 725.0 in model 447, 448
– Adjustment values for multidisk clutch/multidisk brake
– Number Designation Transmission 725.0
– BE27.51-P-1004-01E Clearance in multidisk Contact force for F1 N 600
– BE27.51-P-1005-01E Clearance in multidisk Contact force for F1 N 600clutch K38 clearance adjustment
AR27.51-S-0560-03EA Measure and adjust clearance of multidisk.pdf
– transmission
– Transmission 725.0 in model 447, 448
– Adjustment values for multidisk clutch/multidisk brake
– Number Designation Transmission 725.0
– BE27.51-P-1006-01E Clearance in multidisk Contact force for F1 N 1600
AR27.51-S-7229E Measure and adjust clearance 19.11.2018.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– 105 End disk
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Measure
– Automatic transmission fluids (ATF) BB00.40-P-0236-15A
– (specification 236.15)
AR27.51-S-7230-02EA Measure and adjust clearance of multidisk.pdf
– transmission
– Transmission 725.0 in model 447, 448
– Adjustment values for multidisk clutch/multidisk brake
– Number Designation Transmission 725.0
– BE27.51-P-1003-01E Clearance in multidisk Contact force for F1 N 600
AR27.55-D-0010TSR Remove install oil line on oil cooler 06.03.2020.pdf
– Transmission 722.9 in model 907
– 1 Oil line
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.55-D-0100-01US Disconnect connect automatic transmission oil.pdf
– AR27.55-D-0100-01US Disconnect/connect automatic transmission oil
– lines on radiator
– Transmission 722.683 in model 906 with engine 642.896/898/992/993
– Transmission 722.684 in model 906 with engine 271.951
– Transmission 722.684 in model 906 with engine 646.984/985/986/989/990
– Transmission 722.685 in model 906 with engine 272.979
– Transmission 722.686 in model 906 with engine 651.955/956/957
– Transmission 722.9 in model 906 with engine 642
– Transmission 722.9 in model 906 with engine 651
– 129 589 00 91 00
AR27.55-D-0100A Flush out automatic transmission and torque converter 18.07.2019.pdf
– AR27.55-D-0100A Flush out automatic transmission and torque converter 18.07.2019
– Transmission 722.683/684/685/686
– Modification notes
– 09.02.2012 Value changed: Automatic transmission fluid (ATF), BF27.00-N-1001-01A
– Specifications for Operating Fluids
AR27.55-D-0604WE Remove install return line from integrated oil cooler to automatic transmission 18.07.2019.pdf
– AR27.55-D-0604WE Remove/install return line from integrated oil cooler to automatic transmission 18.07.2019
– Transmission 722.9 in model 906
– 1 Feed line from automatic transmission to hose connection of
– feed line on oil cooler
– transmission
– 4 Return line from oil cooler to integrated oil cooler
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– 2 Detach return line from integrated oil cooler to Transmission 722.9 in model 906 with engine AR27.55-D-0100-01US
– automatic transmission (3) from radiator (8) 642
– Transmission 722.9 in model 906 with engine 651
– *129589009100 Record plug
AR27.55-D-0605WE Remove install feed line from automatic transmission to hose connection of feed 18.07.2019.pdf
– AR27.55-D-0605WE Remove/install feed line from automatic transmission to hose connection of feed 18.07.2019
– line on oil cooler
– Transmission 722.9 in model 906
– 1 Feed line from automatic transmission to hose connection of
– feed line on oil cooler
– to automatic transmission
– 6 Return line from oil cooler to connection fitting of return line
– on automatic transmission
– 7 Oil cooler
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– 3 Detach feed line from automatic transmission AR27.10-D-0501-03WE
– to hose connection of feed line on oil cooler (1)
AR27.55-D-0606WE Remove install feed line on oil cooler 18.07.2019.pdf
– Transmission 722.9 in model 906
– Shown on model 906 without oil cooler integrated in the radiator (8)
– 1 Feed line from automatic transmission to hose connection of
– feed line on oil cooler
– to automatic transmission
– 6 Return line from oil cooler to connection fitting of return line
– on automatic transmission
– 7 Oil cooler9 Retaining clamps
AR27.55-D-0607WE Remove install return line from oil cooler to integrated oil cooler 18.07.2019.pdf
– Transmission 722.9 in model 906
– 1 Feed line from automatic transmission to hose connection of
– feed line on oil cooler
– transmission
– 4 Return line from oil cooler to integrated oil cooler
AR27.55-D-0608WE Remove install return line from oil cooler to connection fitting of return line on 18.07.2019.pdf
– automatic transmission
– Transmission 722.9 in model 906
– 1 Feed line from automatic transmission to hose connection of
– feed line on oil cooler
– to automatic transmission
– 6 Return line from oil cooler to connection fitting of return line
– on automatic transmission
– 7 Oil cooler
– 7 Oil cooler11 Double clamp
AR27.55-D-0609WE Remove install return line from hose connection of return line on oil cooler to 18.07.2019.pdf
– automatic transmission
– Transmission 722.9 in model 906
– 1 Feed line from automatic transmission to hose connection of
– feed line on oil cooler
– to automatic transmission
– 6 Return line from oil cooler to connection fitting of return line
– on automatic transmission
– 7 Oil cooler
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– return line on oil cooler to automatic transmission (5) from automatic transmission
– *129589009100 Record plug
AR27.55-D-0610TSR Remove install oil cooling system feed line 18.07.2019.pdf
– Transmission 722.9 in model 907
– D27.55-A010-79
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
AR27.55-D-0611TSR Remove install oil cooling system return line 18.07.2019.pdf
– Transmission 722.9 in model 907
– D27.55-A011-79
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
AR27.55-D-1000WE Remove install automatic transmission fluid cooler 17.07.2020.pdf
– AR27.55-D-1000WE Remove/install automatic transmission fluid cooler 17.07.2020
– Transmission 722.6/9 in model 906
– D27.55-1103-08
– 1 Additional fan unit 2 Automatic transmission fluid cooler
– Illustration shows model 906 without code
– 2 Automatic transmission fluid cooler
– 3 Screw
AR27.55-P-0001A Flushing out oil cooler lines and oil cooler 06.03.2020.pdf
– Transmission 722.6/7
– Modification notes
AR27.55-S-0001E Flushing out oil cooler lines and oil cooler 16.11.2018.pdf
– Model 447 with engine 274 with transmission 722.9
– Model 447 with engine 651 with transmission 722.9
– Model 448 with engine 274 with transmission 722.9
– 1 Connection fitting
AR27.55-S-0001S Flushing out oil cooler lines and oil cooler 18.07.2019.pdf
– Transmission 722.680/682 in model 639
– Modification notes
– 09.02.2012 Value changed: Automatic transmission fluid (ATF), BF27.00-N-1001-01C
– Specifications for Operating Fluids
AR27.55-S-0600E Remove install oil lines of oil cooling for automatic transmission 15.12.2015.pdf
– AR27.55-S-0600E Remove/install oil lines of oil cooling for automatic transmission 15.12.2015
– Model 447 with engine 274 with transmission 722.9
– Model 447 with engine 651 with transmission 722.9
– Model 448 with engine 274 with transmission 722.9
– S27.55-4512-09
AR27.55-S-0600SD Remove install oil lines of oil cooling for automatic transmission 15.01.2020.pdf
– AR27.55-S-0600SD Remove/install oil lines of oil cooling for automatic transmission 15.01.2020
– Transmission 722.6 in model 639 with engine 646
– S27.55-4502-09
AR27.55-S-0600SJ Remove install oil lines of oil cooling for automatic transmission 12.9.13.pdf
– AR27.55-S-0600SJ Remove/install oil lines of oil cooling for automatic transmission 12.9.13
– TRANSMISSION 722.6 in MODEL 639 with ENGINE 651
– S27.55-4506-09
AR27.55-S-0600SV Remove install oil lines of oil cooling for automatic transmission 20.11.03.pdf
– AR27.55-S-0600SV Remove/install oil lines of oil cooling for automatic transmission 20.11.03
– MODEL 639.601 /603 /605 /701 /703 /705 /711 /713 /811 /813 /815 with ENGINE 112.951 /976
AR27.55-S-7380S Remove install transmission cooling coolant recirculation pump 11.12.2018.pdf
– AR27.55-S-7380S Remove/install transmission cooling coolant recirculation pump 11.12.2018
– Transmission 722.680/682 in model 639
– Shown on model 639 with engine 646
– 2 Unscrew union nuts (4, 5) of oil cooler return *BA27.55-N-1007-01F TRANSMISSION 722.680/682Union nut,
– line and oil cooler feed line oil line to thermostat valve
AR27.57-D-0652TSR Remove install automatic transmission auxiliary oil pump 06.03.2020.pdf
– AR27.57-D-0652TSR Remove/install automatic transmission auxiliary oil pump 06.03.2020
– Transmission 722.9 in model 907
– Modification notes
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove/install
AR27.57-S-0652PS Remove install automatic transmission auxiliary oil pump 06.03.2020.pdf
– AR27.57-S-0652PS Remove/install automatic transmission auxiliary oil pump 06.03.2020
– Transmission 722.9 in model 470, 471 with engine 642
– S27.57-0002-78
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– transmission
– Remove
– outside of transmission range (min. 2 m).
– 2 Remove rear engine compartment lining at AR61.20-S-1105P
– 4 Drain transmission oil from oil pan. AR27.00-S-0200-01PS
–
AR27.60-D-0950A Remove install park pawl mechanism 03.12.2013.pdf
– TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6
– TRANSMISSION 722.683 in MODEL 906.1/2/6/7
– TRANSMISSION 722.684 in MODEL 906.1/2/6/7
– TRANSMISSION 722.685 in MODEL 906.1/2/6/7
– TRANSMISSION 722.686 in MODEL 906.1/2/6/7
– 1 Screw
AR27.60-D-0950TSR Remove install park pawl mechanism 14.07.2019.pdf
– Transmission 722.9 in model 907
– Shown except code ZG1 (All-wheel drive,
– transmission ratio)
– 1 Screw
– 10 Transmission housing
– D27.60-A002-06
– handling of transmission oil. Health risk and safety glasses.
– caused by swallowing transmission oil Do not pour transmission oil into beverage
– bottles.
– Notes on automatic transmission AH27.19-P-0001-01NKB
– Remove
– 1 Remove transmission. AR27.10-D-0005TSR
– 2 Fasten transmission onto assembly stand. AR27.10-D-0600-01TS
– *116589065900 Assembly stand
AR27.60-D-0950WE Remove install park pawl mechanism 21.12.11.pdf
– TRANSMISSION 722.9 in MODEL 906
– 1 Transmission housing
– 81 Range selector lever
– 1 Remove automatic transmission AR27.10-D-0502W
– 2 Fasten transmission on assembly stand AR27.10-D-0600-01WE
– *116589065900 Assembly stand
AR27.60-S-0950E Remove install park pawl mechanism 17.02.2016.pdf
– Model 447 with engine 651 with transmission 722.9
– Model 447, 448 with engine 274 with transmission 722.9
– 1 Transmission housing
– 81 Range selector lever
– 1 Remove transmission AR27.10-S-0500E
– 2 Fasten transmission on assembly stand AR27.10-S-0600-01E
– *116589065900 Assembly stand
– 4 Detach rear engine support Model 447 with engine 651 with transmission AR22.10-S-4360E
– 722.9
AR27.60-S-0950S Remove install park pawl mechanism 17.12.10.pdf
– TRANSMISSION 722.6 in MODEL 636, 639
– Shown without CODE (ZG2) Permanent all-
– 1 Transmission housing
– 2 Selector lever
Automatic transmission – Checking All models.pdf
– Automatic transmission – Checking, All models
– correcting oil level
– On vehicles with automatic transmission, shift transmission to “P”.
– A. Checking
– Closing lever, transmissions 722.0, 722.1 Closing lever, transmissions 722.3, 722.4, 722.5
– Oil level, transmissions 722.0, 722.1 Oil level, transmissions 722.3, 722.4, 722.5
– Note
BB00.40-P-0231-00A General gear oils.pdf
– application into: Frequently the transmission oils fulfill multifunctional requirements,
– Hypoid gear oils, sheet 235.0/.6/.7/.8/.15/.16/.20/.31/.61/.62 which is why they are used in a wide variety of transmission desi gns
– and hydraulic systems. However, where very specific technological Transmission oils, sheet 235.1/.3/.4/.5/.10/.11/.12/.13/.27/.28/.29/.41/
– properties of the transmission oil are required, special transmission oils .71/.72/.73/.74, 236.24
– had to be formulated for these major assemblies. These are listed on Transmission fluids (ATF), sheet 236.1/.2/.3/.6/.7/.8/.9/.10/.11/.12/.13/
– separate sheets of the MB Specifications for Operating Fluids and .14/15/.17./.20/.21/.22/.24/.25/.26/.41/.81/.91, 238.22, 239.21
– explain the large number of sheets for transmission oils.
– The Mercedes-Benz standard for the corresponding lubricant quality
BB00.40-P-0231-02A Specified transmission oils commercial.pdf
– BB00.40-P-0231-02A Specified transmission oils (commercial
– vehicle, van) – Overview
BB00.40-P-0236-14A Automatic transmission fluids ATF.pdf
– BB00.40-P-0236-14A Automatic transmission fluids (ATF)
– (specification 236.14)
– Service Information bulletin: Specifications for Transmission 722.6 SI00.40-P-0014A
– Operating Fluids for automatic transmission Transmission 722.9
– Transmission 700.77
– Transmission 722.6
– Transmission 722.9
– 5-speed automatic transmission 722.6
BB00.40-P-0236-15A Automatic transmission fluids ATF Use in vehicles major assemblies see.pdf
– BB00.40-P-0236-15A Automatic transmission fluids (ATF) Use in vehicles/major assemblies, see
– (specification 236.15)
– Service Information bulletin: Specifications for Transmission 722.9 SI00.40-S-0014A
– Operating Fluids for automatic transmission
– Service Information bulletin: Specifications for Transmission 722.9 SI00.40-P-0014A
– Operating Fluids for automatic transmission Transmission 724.2
– Transmission 722.9
– Transmission 724.2
– Transmission 725.0 in model 205, 213, 217, 218, 222, 238, 253, 257, 290
– Only for transfer case
Should be used BB00.40-P-0231-01A Specified gear oils cars cross-country.pdf
– Automated manual transmission 717.4 in model 450, 452
– Automated manual transmission 717.4 in model 451, 454
– DCT (Twinamic) 700.410/411 in model 453
– Manual transmission 700.120/121/122/123 in model 453
– Passenger car, sheets 235.0 to 235.74
SI00.40-P-0014A Service Information bulletin Specifications for Operating Fluids for automatic 06.12.2018.pdf
– transmission
– Transmission 722.6/9, 724.2, 725.0/1
– Modification notes
– 7-speed automatic transmission 724.2 We hereby inform you about current changes to the Specifications
– Only transmission oil as per Specifications for Operating Fluids Sheet for Operating Fluids:
– 236.15 5-speed automatic transmission 722.6: may now be used.
– 9-speed automatic transmission 725.0/1 Only transmission oil as per Specifications for Operating Fluids Sheet
– Only transmission oil as per Specifications for Operating Fluids Sheet 236.14 may be used.
– 236.17 7-speed automatic transmission 722.9 except codeA89 may now be used!
– Exception: Only transmission oil as per Specifications for Operating Fluids sheet
– Transmission 722.6 may not be filled with FE-ATF 134 236.14 may be used. and ATF D97 .
– 7-speed automatic transmission 722.9 with codeA89
– Only transmission oil as per Specifications for Operating Fluids Sheet
– 236.15 may now be used.
– to ensure that 7-speed automatic transmission 722.9 is filled correctly. 236.17)
– because these oils must never be mixed with other oils. The diagnostics system displays a message referring to the specified
– transmission oil before reading out the transmission oil temperature. Exception:
– Transmission 722.9 can be identified by the differently shaped oil pan Transmission 722.6/9, the associated electrohydraulic controller units
– (see picture 1 and picture 2 ). and torque converters, which are available as a replacement part, are
SI00.40-S-0014A Service Information bulletin Specifications for Operating Fluids for automatic 19.11.2018.pdf
– transmission
– Model all with transmission 722.6/9
– Exception: We hereby inform you about current changes to the Specifications
– Transmission 722.6 may not be filled with FE-ATF 134 for Operating Fluids. and ATF D97 .
– 7-speed automatic transmission 722.9: 5-speed automatic transmission 722.6:
– Only transmission oil as per Specifications for Operating Fluids Sheet Only transmission oil as per Specifications for Operating Fluids Sheet
– 236.15 may be used. 236.14 may be used.
– to ensure that 7-speed automatic transmission 722.9 is filled correctly: These oils must never be mixed with other oils.
– In XENTRY diagnostics a message is displayed referring to the Exception:
– specified transmission oil before reading out the oil level check. Transmission 722.6/9, including electrohydraulic controller units and
– The documentation of the filling process is available in the WIS (see torque converter, which are available from the parts serv ice, are filled
– D-2702TS for model 907). case, the transmission, controller unit and torque converter do not
– have to be cleaned. The transmission can be filled with the corresponding gear oil (as per this Service Information bulletin) immediately after it has been installed.
– The modified Specifications for Operating Fluids are available in
Technical modifications Automatic transmission 722.3 I 09 88.pdf
– Technical modifications Automatic transmission 722.3 I 09/88
– Designation Type and reason for change Introduced Op. No.
– 27 430 Transmission housing, Enlarged feed B1 (cross-section change in oil 04/89
– vehicles with 8-cylinder distributor plate. 27 640
– 27 640 Transmission housing Oil pipe to governor lubrication omitted, except 04/89
– vehicles with 4MATIC Phased in on
– transmissions
– 27 640 Brake band B2 with Used to improve shift quality 10/89
Technical Modifications Automatic Transmission 722.4 09 89.pdf
– Technical Modifications Automatic Transmission 722.4 09/89
– Designation Nature and reason for modification Implementation dates Op. No.
– Transmission End No.
– Red temperature inductor For improving 2 – 3 September 1983 003
– transmission 722.400 gearshifts
– Modified control pressure Functional improvement in October 1984 110
Technical modifications Automatic transmission 722.4 10 89.pdf
– Technical modifications Automatic transmission 722.4 10/89
– Operation n°
– Transmission shift Installed for more rapid heatup of 09/89 27-115
– point retard catalytic converter. 27-330
Service manual Mercedes 722 Transmission
29,99 $
Format: PDF
Type: Repair Manuals
Size: 45,8 Mb
203 PDF files
Attention! By purchasing this item, you are gaining access to a dynamic catalog. Please note that your access will be valid for 30 days only. During this time, you can download all the files available in the catalog.
-
Service manual Mercedes 725 Transmission
29,99 $
ADD TO CART -
Service manual ATSG Mercedes 722.4 and 722.3
2,99 $
ADD TO CART -
Service manual Mercedes 718 Transmission
29,99 $
ADD TO CART -
Service manual 722.6 ATSG Mercedes transmission
2,99 $
ADD TO CART -
Service manual Mercedes 712 Transmission
29,99 $
ADD TO CART -
Service manual 722.3 Mercedes Automatic 4G-Tronic transmission
2,99 $
ADD TO CART
There are no reviews yet.